kevindd99202 Posted April 8, 2013 Share Posted April 8, 2013 Prema, regarding the BIOS mod you gave me for my NP8130 I see some Warning events under event viewer with this message:The speed of processor 1 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 3 seconds since the last report.Is that normal? Link to comment Share on other sites More sharing options...
Khenglish Posted April 8, 2013 Share Posted April 8, 2013 Thank you!It works well![ATTACH=CONFIG]6863[/ATTACH]After change T2 mode,I could pass memtest86.The error had come out by the memtest at the T1.How big of a performance hit are you getting for running T2? I've been trying to run minimum latency so I run 1866 10-11-9 T1.Also noticed that my memory is very temperature sensitive. Going to attempt putting copper flashing on it and see if it helps. Link to comment Share on other sites More sharing options...
newtsy Posted April 9, 2013 Share Posted April 9, 2013 Hi Prema, If I want to run the P170EM bios in my P150EM, should I first flash to the stock P170EM, I am going to order a 3920XM and would like to be able to use XTU. Or is there a chance that you will be able to enable XTU on the P150EM bios?Is flashing to the P170EM bios even a good idea, I have read that it is working for some?Thanks Again Link to comment Share on other sites More sharing options...
Acro Posted April 9, 2013 Share Posted April 9, 2013 How big of a performance hit are you getting for running T2? I've been trying to run minimum latency so I run 1866 10-11-9 T1.Also noticed that my memory is very temperature sensitive. Going to attempt putting copper flashing on it and see if it helps.The score became somewhat good. at 3DMark11 Physics ScoreDDR3-1600 9-9-9-24 1T:9618DDR3-2133 12-12-12-36 2T:9959I'll try to put copper seat and 1T. Link to comment Share on other sites More sharing options...
luoxia Posted April 9, 2013 Share Posted April 9, 2013 Thank you!It works well![ATTACH=CONFIG]6863[/ATTACH] After change 2T mode,I could pass memtest86. The error had come out by the memtest at the 1T. Hello Seeking AIDA64 memory test chart As shown below Thank you! Link to comment Share on other sites More sharing options...
zymphad Posted April 10, 2013 Share Posted April 10, 2013 PREMA, I think your latest BIOS is preventing zero-core on AMD. It's always running very hot here. Normally, when it's idle, the temps will reduce to around 25C. But since the V2, it never goes below 45C for me, therefore the fans never fully turn off. Link to comment Share on other sites More sharing options...
Guest Posted April 10, 2013 Share Posted April 10, 2013 Prema, regarding the BIOS mod you gave me for my NP8130 I see some Warning events under event viewer with this message:The speed of processor 1 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 3 seconds since the last report.Is that normal?I would say that's the regular temp or TDP throttle = to be expectedHi Prema, If I want to run the P170EM bios in my P150EM, should I first flash to the stock P170EM, I am going to order a 3920XM and would like to be able to use XTU. Or is there a chance that you will be able to enable XTU on the P150EM bios?Is flashing to the P170EM bios even a good idea, I have read that it is working for some?Thanks AgainNo problems you can use my P170EM mod to flash BIOS & EC in one go, fan profiles are different on P17 as in more silent & speeding up on higher temps as it was designed for higher/hotter running CPUs.PREMA, I think your latest BIOS is preventing zero-core on AMD. It's always running very hot here. Normally, when it's idle, the temps will reduce to around 25C. But since the V2, it never goes below 45C for me, therefore the fans never fully turn off.Maybe the driver? Flash the latest stock BIOS from the other sticky here to see if problem persists. Link to comment Share on other sites More sharing options...
kevindd99202 Posted April 11, 2013 Share Posted April 11, 2013 I would say that's the regular temp or TDP throttle = to be expectedWell, it isn't supposed to be throttling when having regular operations, right? My average temps are in the mid-50's. With my desktop computer, I can reach up to 90C and I don't get those event viewer errors? Link to comment Share on other sites More sharing options...
zymphad Posted April 11, 2013 Share Posted April 11, 2013 Also I think the latest EC is 14. Link to comment Share on other sites More sharing options...
Guest Posted April 11, 2013 Share Posted April 11, 2013 Well, it isn't supposed to be throttling when having regular operations, right? My average temps are in the mid-50's. With my desktop computer, I can reach up to 90C and I don't get tuthose event viewer errors?The CPU Turbos up to its TDP limit for a certain amount of time and then throttles, you can raise TDP limits in XTU or, if the cooling is sufficient, even avoid throttle all together. Some CPUs don't even reach thrir advertised maximum Turbo Speed without those manual adjustments. Also I think the latest EC is 14.Saw it on Sager, haven't checked or seen stock Clevo versions yet... Link to comment Share on other sites More sharing options...
kevindd99202 Posted April 11, 2013 Share Posted April 11, 2013 The CPU Turbos up to its TDP limit for a certain amount of time and then throttles, you can raise TDP limits in XTU or, if the cooling is sufficient, even avoid throttle all together. Some CPUs don't even reach thrir advertised maximum Turbo Speed without those manual adjustments.Saw it on Sager, haven't checked or seen stock Clevo versions yet...Understood, but what I'm wondering about is why does it not happen on my desktop with an i5-2500K CPU? That also has Turbo. Link to comment Share on other sites More sharing options...
luoxia Posted April 11, 2013 Share Posted April 11, 2013 The CPU Turbos up to its TDP limit for a certain amount of time and then throttles, you can raise TDP limits in XTU or, if the cooling is sufficient, even avoid throttle all together. Some CPUs don't even reach thrir advertised maximum Turbo Speed without those manual adjustments.Saw it on Sager, haven't checked or seen stock Clevo versions yet...http://forum.techinferno.com/clevo-sager/3319-p170hm-memory-4gx4-%3D-2133mhz.html Link to comment Share on other sites More sharing options...
Guest Posted April 11, 2013 Share Posted April 11, 2013 Understood, but what I'm wondering about is why does it not happen on my desktop with an i5-2500K CPU? That also has Turbo. Because that CPU/mobo/cooling combination apparently doesn't breach its TDP limits...even identical cpu models on the same system often behave slightly differently... http://forum.techinferno.com/clevo-sager/3319-p170hm-memory-4gx4-%3D-2133mhz.html Glad the mod worked for you! Looks like I'll have to make 2T mods public as they behave differently to automatic 2T mode...as if it is not enough time spend already to maintain all those mods... Link to comment Share on other sites More sharing options...
kevindd99202 Posted April 11, 2013 Share Posted April 11, 2013 Because that CPU/mobo/cooling combination apparently doesn't breach its TDP limits...even identical cpu models on the same system often behave slightly differently... Glad the mod worked for you! Looks like I'll have to make 2T mods public as they behave differently to automatic 2T mode...as if it is not enough time spend already to maintain all those mods... Ah, so this behavior is normal for a laptop? Link to comment Share on other sites More sharing options...
Guest Posted April 11, 2013 Share Posted April 11, 2013 Ah, so this behavior is normal for a laptop?Its "Intel Normal"...LOL Link to comment Share on other sites More sharing options...
savageX Posted April 11, 2013 Share Posted April 11, 2013 hello, this week i have buy a clevo p170em with 3630qm and 680m. I have seven 64 instaled and I would like to know if when I will flash bios, system will crash (update of sata ahci controleur) and if I can flash 680m after this?thanks for your help Link to comment Share on other sites More sharing options...
savageX Posted April 14, 2013 Share Posted April 14, 2013 thanks for your job.Fn + 9 works perfectly and help for some bench.boot logo is now "colored"can you ad an option to enable/disable intel hypertreading on P170em or it's impossible?good luke for next.thanks a lot Link to comment Share on other sites More sharing options...
Guest Posted April 14, 2013 Share Posted April 14, 2013 hello, this week i have buy a clevo p170em with 3630qm and 680m. I have seven 64 instaled and I would like to know if when I will flash bios, system will crash (update of sata ahci controleur) and if I can flash 680m after this?thanks for your help Right now the new RAID versions have a boot delay issue only in Win7 RAID mode, this will be fixed in the next release. You can flash the GTX680M whenever you want... Link to comment Share on other sites More sharing options...
Guest Posted April 15, 2013 Share Posted April 15, 2013 Updated OP with BIOS v17 for P170EM Link to comment Share on other sites More sharing options...
Guest Posted April 16, 2013 Share Posted April 16, 2013 EDIT:P170EM, P150EM, P151EM, P370EM & P370EM3 versions of PM v1.0.3 now available in OP:- Updated Clevo base to v17 (P170EM)- Legacy RAID oROM downgraded to v11.6.0.1702 (TRIM without WIN7 RAID boot delay bug)- Added 2T EDITION (Tad slower, but proven more stable with difficult RAM like 2133Mhz & 32GB) Link to comment Share on other sites More sharing options...
N3ST Posted April 17, 2013 Share Posted April 17, 2013 HEllo,I have a question regarding the 7970m vbios, is the vbios updated with every bios update, or do I need to update it my self?If I have to do it my self, wich version is the latest version and compatible with my P170EM?Thank you in advanceN3ST Link to comment Share on other sites More sharing options...
Guest Posted April 17, 2013 Share Posted April 17, 2013 HEllo,I have a question regarding the 7970m vbios, is the vbios updated with every bios update, or do I need to update it my self?If I have to do it my self, wich version is the latest version and compatible with my P170EM?Thank you in advanceN3STThe vBIOS is separate on P-Series models. Not sure atm about the latest version... Link to comment Share on other sites More sharing options...
Sekence Posted April 17, 2013 Share Posted April 17, 2013 Good job. I didn't updated for my p150EM (8 GB RAM / 1333Mhz) since there is nothing for it. But this show that you'r following the thread attentively Link to comment Share on other sites More sharing options...
luoxia Posted April 17, 2013 Share Posted April 17, 2013 EDIT:P170EM, P150EM, P151EM versions of PM v1.0.3 now available in OP: - P170EM BIOS base updated to v17 - Legacy RAID oROM downgraded to v11.6.0.1702 (TRIM without WIN7 RAID boot delay bug) - Added 2T Edition (Better 2133Mhz & 32GB RAM support) Hope P_HM can unlock as soon as possible to Link to comment Share on other sites More sharing options...
Guest Posted April 17, 2013 Share Posted April 17, 2013 Hope P_HM can unlock as soon as possible to Ha ha ha, me too. Will repair my P170HM3 soon and then focus on the HMs Link to comment Share on other sites More sharing options...
Recommended Posts