Jump to content
EwinRacing Flash Series Gaming Chairs
wamendonesjr

Help on ASUS G75VW [OVERHEATING PROBLEM]

Recommended Posts

I have tried the following and my laptop still shuts off randomly when playing games:

1. I have already cleaned the fans and parts from dust

2. I have already put brand new Thermal Grease

(I followed the recommend amount found on this picture)

post-35735-14495000019658_thumb.jpg

THINGS I NOTICED:

1. In Safe mode, my laptop does not shutdown randomly

2. My BIOS VERSION : 04.06.05

3. My Core Temps (After Long Use)

post-35735-14495000019787_thumb.jpg

4. Hot Air blowing out of the back exhaust[on the right side] after few minutes of start up (idle)

post-35735-14495000019918_thumb.jpg

SHOULD I UPDATE THE BIOS to this:

http://forum.techinferno.com/asus-gaming-notebook-forum/2538-%5Bg75vw%5D-modified-bios-vbios-higher-overclocking.html

WILL THIS FIX THE PROBLEM?

Share this post


Link to post
Share on other sites

It may be bad paste job! You should spread as thin as possible layer on whole crystal not just put a drop in the middle (its works only for PC's) also repast your gpu. Try to use arctic cooling mx4 paste.

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

also the paste you are using is generic. Try some of the quality stuff, i believe its called arctic silver with diamond like silver particles. Much more conductive and far better heat transfer.
Also if you have overheated and burned your cpu it may bee too late to go back this behavior is not uncommon to me, however it wont hurt to try and use higher quality paste.

FYI you can drill holes under your fans to further increase cooling capacity. Here is a link for a How TO
 


a

Share this post


Link to post
Share on other sites

59° is not higher for laptop.. Overtemp.protection is more at 85-95°c.

 

Share this post


Link to post
Share on other sites

Hi, 

You should check the temperature under load.  Try some benchmark like 3dmark with cpuz and gpuz open,  that will let you check both temperatures GPU and CPU.  If you can post some capture. 

Share this post


Link to post
Share on other sites

i did the drilling mod, and it was worth the process, dropped the temps a good amount.

Share this post


Link to post
Share on other sites

interesting tht drilling mode, but i was not sure about the succes of, like tht more air pass from the fan but usually to force the air to pass completly inside the sistem will have better effect, strange... but interesting

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By Guardian241
      So I just received a 980m in the post and after installing it I was greeted by multiple system crashes on my Alienware m17xr4 and was unable to install new drivers.

      Is there a step in the intallation process I missed? A bios setting I was supposed to change? The laptop is already set to UEFI mode in preperation for this and upon putting the old 680m back in the system it now works again. I have heard that I need to change INI files to install drivers but I expected it to at least function without large bugs such as these. Do you think that this GPU is faulty or have I done something wrong?
       
      Thanks for any help you can give.
       
      - M
    • By Guardian241
      Hi,
       
      I've recently got my hands on an M17x R4 Alienware Laptop from 2013 which I love. I've replaced the screen, keyboard, RAM, and hard drive to make it into a fully modern laptop. However, I'm currently waiting on a replacement for the 680m GPU with a 980m from ebay. My question for you all is, do I need to do anything with the BIOS to make this 980m work? Is there a way to prevent the laptop from using Intel HD Graphics with Optimus? I think the Intel HD Graphics on this laptop are currently broken as I see static-looking dots flash on the screen. (See image below for example). My theory is that because Intel HD Graphics with Optimus is still in-use while in-game, the dots are being caused by it.
       
      Thanks for any help in advance.
       
      - M
       

       
       
    • By narbardarse
      ok, so, i have a serious problem atm.
      im trying to mod my bios so that i can go past the normal overclocking limit. however, everytime i try to do it, it always says "file size does not match existing bios size!", and it's really annoying, since i had to find everything myself, as no one else online tried this on my specific model, besides me. (which surprises me, really)
      this is the guide im following:
      So this is my detailed description how I managed to mod and overclock my GTX 960M in my Lenovo Y50-70. Please note: it is very dangerous to play with the BIOS, so you need to be very careful! I take NO RESPONSIBILITY for any damage or misuse of the information below! Use it AT YOUR OWN RISK!
       
      -------
       

      Necessary tools:
      A. Fptw64 from Intel (9.5 or above)
      http://forum.hwbot.org/showthread.php?t=75024
      B. PhoenixTool (2.50 or above)
      C. Maxwell II BIOS Tweaker (1.36)
      https://www.techpowerup.com/downloads/2562/maxwell-ii-bios-tweaker-v1-36/
       
      -------------------------
       
      How to flash Modded BIOS:
      0. Flash the latest (3.03 now) official BIOS
      1. From Windows, start 'cmd' as Administrator and read your your BIOS via Fptw64:
         Fptw64 -d BIOS.ROM -bios
      2. Reboot, enter your BIOS and check "Enable downgrading BIOS" feature (we need to downgrade first in order to flash the modded BIOS)
      3. From Windows, downgrade to 1.13 (this is necessary because the newer BIOSes have protection against mod-ding)
      4. After reboot & reflash, start Windows, then enter standby, wait a bit, then wake up the machine
      5. Create your modded BIOS, see separate list below
      6. Start 'cmd' as Administrator and write your _modded_ BIOS via Fptw64:
         Fptw64 -f BIOS_MODDED.ROM -bios
       
      -------------------------
       
      How to create modded BIOS (point 5 above):
      5.1 Start PhoenixTool.exe from Phoenix Tool 2.50 and open your previously saved original BIOS.ROM from point #1 above
       .2 The tool analyses it and shows some messages, click OK
       .3 Now you can find your vBIOS in the "DUMP" subfolder in the folder containing your BIOS.ROM, with the file name:
          BE13645B-2C2C-44D2-A64F-0EA052C34597_1796.ROM
       .4 Create your modded vBIOS, see separate list below -> let's call it 960M_OC.MOD
       .5 Click on "Structure"
       .6 Open "EFI BIOS" tag
       .7 Open second "File Volume {7A9354D9-...}" tag
       .8 DXE Core -> Compressed Section -> Raw section -> File Volume {7A9354D9-...}
       .9 In the very long list, find the following tag (usually displayed at around 80% of the list):
          Freeform {BE13645B-2C2C-44D2-A64F-0EA052C34597}
          This is the item containing the latest vBIOS
       .10 Open the tag, then "GUID defined section", then click on Raw section. "Internal number" (in the top right corner) should be 1796 for BIOS 3.03.
       .11 Click on "Replace" and select your modded vBIOS (called 960M_OC.MOD above)
       .12 Click exit "Exit" and say Yes to "Save changes?"
       .13 Close the Phoenix Tool; now you should have your BIOS.ROM updated (the original will be saved as BIOS.ROM.OLD for safety)
       
      -------------------------
       
      How to create modded vBIOS (point 5.4 above):
      Use Maxwell II BIOS Tweaker to change BE13645B-2C2C-44D2-A64F-0EA052C34597_1796.ROM;
      5.4.1 Open the ROM
         .2 Change "Boost Clock" on "Common" tab to the new boost-ed maximum value
         .3 On "Boost table" tab, use the slider in the right bottom corner to increase your max boost-ed value to the same number
         .4 On "Boost states" tab, at P00 profile, change the MAX values in the GPC, L2C and XBAR fields to the same max boost-ed value
         .5 Save your modified BIOS and rename it to 960M_OC.MOD
       
      (My boost-ed max value was 1359 MHz. I could then use MSI Afterburner's software tuning -> my 960M could reach 1454 MHz without voltage increase.)
      i know that it's for a different laptop, but its basically the same
      ill provide more info when im home
    • By Toloni
      I am very aware of the healthy skepticism of most if not all of you. I therefore kindly ask of you not to spew out the fact that its impossible to build a laptop at me but instead attempt to help me to make this somewhat possible for the next person interested in the idea.
       
      I already have:
      somewhere to buy a screen: https://www.laptopscreen.com/English/ somewhere to buy a motherboard, CPU, GPU, RAM, storage and other things although I would be very interested should you recommend other places where I can get these  
      I will build the cooling system myself
       
      I need:
      somewhere to buy a laptop shell (I am aware of how difficult it is to find one and am therefore very flexible on all other components) somewhere to buy a power supply  
      Thank you very much for helping me and pushing the possibility of building a custom laptop ever so slightly more realistic
       
      Toloni
    • By IveGotRoot
      I have recently upgraded my laptop(an M6800 firepro 6100) and replaced it with an GTX 980m. Nvidia says that the latest driver(461) supports my card but i can only install up to 388.13 Ive tried to mod it but i can't figure it out. I can run the latest linux driver tho
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.