bloodcool000 Posted September 18, 2015 Share Posted September 18, 2015 Reinstall all drivers Link to comment Share on other sites More sharing options...
clearwater Posted September 18, 2015 Share Posted September 18, 2015 OK by me. I also have an eBay account. Pm meSorry, but it sold on Ebay. I will let you know if for some reason the buyer backs out and its back for sale. Good Luck and have fun with your portable gaming machine. Link to comment Share on other sites More sharing options...
Vapochilled Posted September 18, 2015 Share Posted September 18, 2015 Can you point me out if I can use my HP 230W adapter and mod it, or if I really need that Dell adaptor?The other question is: were you using the dell to feed the akitio + graphic card? Or you had any power raiser? Or any mod of power stability? Link to comment Share on other sites More sharing options...
Luna Posted September 20, 2015 Share Posted September 20, 2015 Hi. I have some issue with setup1.3. I've installed 'Setup1.3', then faced the wall. I am at a loss. I've already read the articles involved in my problems on this website. Almost all the pages I have to read, I have read, I think.(of course I might have missed something, that because I can't get through my situation) ABOUT MY PC Lenovo edge e450 core-i7 5500U Chipset: Intel Broadwell-U PCH-LP(Baseline) Chipset Win 7 pro 64bit On board GPU AMD Radeon R7 M260(slightly better than intel on-board graphics) 8gb memory Just in case my TOLUD is 2.75GB Probably you can't read because of Japanese. SCN010.BMP I want to use GTX960 by msi GPU. The mPCI cable extends from m.2(keydA,E) wifi slot. So, white-listed problem also occured. But, thanks to Tech Inferno Fan's advice on this forum,(I can't find URL now) I managed to make PC recognize GTX960.(First,set on wifi module, then, during sleep mode, change wifi module to m.2-mPCI adapter.) Then, next, Error12 occured. That's why I ask you about"Setup 1.3". What I want to ask is: 1. in the following URL, there is a person who has quite similar problem http://forum.techinferno.com/<wbr>diy-e-gpu-projects/2123-diy-<wbr>egpu-setup-1-30-previously-<wbr>setup-1-x-2.html The article no. is #12 Do the set-up procedure, right clicking "setup-disk-image" and selecting "Run as administrator" , then below massage shows. ------------------------------<wbr>------------------------------<wbr>-from here ******************************<wbr>******************** BIG WARNING!! mkdevcon: PCI BUS section NOT found ******************************<wbr>******************** If you are using a non-English language, then please edit the following: v:\config\devcon.txt and remove the "PCI BUS" section that will be in another language. Otherwise the addresses referred to in that section will be such that the the complete PCI BUS will be excluded during compact and compaction will find no solutions(fail). ------------------------------<wbr>------------------------------<wbr>-----------------------end http://forum.techinferno.com/<wbr>diy-e-gpu-projects/5096-egpu-<wbr>dell-studio-1747-not-working-<wbr>easily.html This URL also includes similar situation. Though I already deleted "ACPI\PNP0A08\0 ・・・・・・ IO : 0d00-ffff " codes, the problem still exists. In addition to that, I don't know this action is right or not. This is first problem. 2. Second is the fatal point. Your guidance : "Rebooting will now show a "Setup 1.x" bootitem in the Win7/8 (or XP if still using it) bootmenu. Select Setup 1.x then Setup 1.30-menu-based" Reboot, and "Setup 1.3" shows, then select "3. DIY eGPU Setup 1.30 : menu-based" This massage shows. What 'iport functionality disabled for now' means? Why "disabled now"? Then, entering 'setup' or pressing F10 results in following picture. Of course, this picture is after pressing F1. Then, I do not understand what I have to do, I ran No.1 "iport scan". So, following codes show. I can't understand this massage, but I've done all I could do. Below two photos show what I did.(I ran two compaction menu, but PC freezed on 1h) Your reply in this thread,"Looks like you have found a bug on the AMD platform where the refresh (F5) drops out to DOS. A workaround for the time being is simply type 'setup' or hit F10 to return to the menus. Then proceed to highlight PCI compaction->Run compact and hit F1." But, I can't find "highlight PCI compaction->Run compact" at all. Whare is the menu? What can I do? I do want to get through this situation. So please help me! My English is poor, so please ask me when you read my article and find something wrong. Regards. Link to comment Share on other sites More sharing options...
flyfree Posted September 21, 2015 Share Posted September 21, 2015 Thanks for the url. I'm able to use GTX 980 now. But the issue is my 2014 15" MBP with 750M reboots whenever it wakes up from sleep mode. Don't you have this problem? Link to comment Share on other sites More sharing options...
EpicCraizy Posted September 22, 2015 Share Posted September 22, 2015 good project Link to comment Share on other sites More sharing options...
EpicCraizy Posted September 22, 2015 Share Posted September 22, 2015 good Link to comment Share on other sites More sharing options...
dreadfury Posted September 22, 2015 Share Posted September 22, 2015 hi, After some helps from nando and searched various related threads i was able to setup my egpu GTX 780 Ti but games kept running with iGpu, i want to run with my internal LCD display (external monitor running fine) i've read that optimus might not work with windows 10,my specs:Alienware m17x r4 bios version a13intel i7 3630qmIgpu : intel HD 4000dgpu gtx 680megpu gtx 780 tiram 8gbwindows 10 x64 turned off dgpu in setup 1.30, pci compaction and chainloaded into windows all fine i've installed nvidia desktop driver v355.82 x64, since my bios doesnt allow idpu to be turned off, i set default graphic processor to gtx 780 ti but performance still the same as if running on igpu ( <10 fps) i tried to disable the igpu in device manager but it seems the internal is attached to the igpu so that would not help. should i install another specific driver to get my games running on egpu? Please help me ,thanks Link to comment Share on other sites More sharing options...
LordKarango Posted September 22, 2015 Share Posted September 22, 2015 TBH, has external gpus not been a thing with previous version of thunderbolt? I thought it was issues regarding drivers/ gpu manufacturers, that stopped them from coming into fruition. Link to comment Share on other sites More sharing options...
zerov01d Posted September 22, 2015 Share Posted September 22, 2015 sorry had to edit post. Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 This is really helpful, thank you! Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 This is very help, thank you! Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 Hi, anyone done upgrading CPU on M17x R4 before? Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 Cool..... Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 I hope this would work for me...5th post yeah... Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 Thanks for sharing.. Link to comment Share on other sites More sharing options...
waynehwm Posted September 23, 2015 Share Posted September 23, 2015 This is really helpful, thank you! Link to comment Share on other sites More sharing options...
tuckerchapin Posted September 24, 2015 Share Posted September 24, 2015 This is a ridiculously n00bish question, but all of the discussion on this site seems to be surrounding Optimus, I'm on a MacBook Air which has a shit display -- I'm fine with the external monitor I have connected, but I cannot for the life of me figure out how to get the Nvidia drivers installed to use my eGPU. When I try and boot into Windows 10 with the eGPU plugged in it crashes before it gets the little boot loading icon. And when I try to install the Nvidia drivers without booting with it plugged in (plugging it in after the fact) I get the error that the installer could not find compatible hardware. People seem to be having success using an external monitor but I have no luck...? Link to comment Share on other sites More sharing options...
tuckerchapin Posted September 24, 2015 Share Posted September 24, 2015 This is a ridiculously n00bish question, but all of the discussion on this site seems to be surrounding Optimus, I'm on a MacBook Air which has a shit display -- I'm fine with the external monitor I have connected, but I cannot for the life of me figure out how to get the Nvidia drivers installed to use my eGPU. When I try and boot into Windows 10 with the eGPU plugged in it crashes before it gets the little boot loading icon. And when I try to install the Nvidia drivers without booting with it plugged in (plugging it in after the fact) I get the error that the installer could not find compatible hardware. People seem to be having success using an external monitor but I have no luck...? Link to comment Share on other sites More sharing options...
Dschijn Posted September 24, 2015 Share Posted September 24, 2015 @tuckerchapin: Wrong thread! Link to comment Share on other sites More sharing options...
tns1 Posted September 26, 2015 Share Posted September 26, 2015 hi @Tech Inferno Fan. sorry for my bad english.i have a problem with egpu setup 1.30https://www.youtube.com/watch?v=EXfP_6oiCigmy friend from ''turkish egpu forum'' have same issue. I'm helping him.my pc: lenovo ideapad y500friends pc: acer aspire 5750gbios setting: legacy bioswe have mkdevcon error. because, we use windows7 turkish language version.you say: for solution delete pci bus line in devcon.txtwe did it.when pc rebooting there is no os selection between windows7 and eGPU-setup-1.30where we make mistakes.edit: problem solved. mbr recreated with bootice v1.3.3.2 Link to comment Share on other sites More sharing options...
uchy74 Posted September 27, 2015 Share Posted September 27, 2015 Thank you for the tuto i download refind but installation of REFIND is not compatible with Windows 10 have you the good instruction to install refind to Windows 10. Link to comment Share on other sites More sharing options...
uchy74 Posted September 27, 2015 Share Posted September 27, 2015 Hello thank you for the tutoriali have Windows 10, installation of refind is not compatible for this windows.have you got the correct instruction for installe refind in this OS Link to comment Share on other sites More sharing options...
uchy74 Posted September 27, 2015 Share Posted September 27, 2015 Hello i have MacBook Pro with 370mif i install Windows 10 in uefi mode, and i plug my external cg, windows boot atomaticaly aboveI will not have to disable the 370mwhen i plug my external cg error 31 but my Windows is install mode legacy (mbr partition) Link to comment Share on other sites More sharing options...
buzing Posted September 27, 2015 Share Posted September 27, 2015 Thats incredible... never thought you could plug a EGPU on the mac.. hahaha. Nice set up btw Link to comment Share on other sites More sharing options...
Recommended Posts