Luna

Hi. I have some issue with setup1.3. I've installed 'Setup1.3', then faced the wall. I am at a loss. I've already read the articles involved in my problems on this website. Almost all the pages I have to read, I have read, I think.(of course I might have missed something, that because I can't get through my situation) ABOUT MY PC Lenovo edge e450 core-i7 5500U Chipset: Intel Broadwell-U PCH-LP(Baseline) Chipset Win 7 pro 64bit On board GPU AMD Radeon R7 M260(slightly better than intel on-board graphics) 8gb memory Just in case my TOLUD is 2.75GB Probably you can't read because of Japanese. SCN010.BMP I want to use GTX960 by msi GPU. The mPCI cable extends from m.2(keydA,E) wifi slot. So, white-listed problem also occured. But, thanks to Tech Inferno Fan's advice on this forum,(I can't find URL now) I managed to make PC recognize GTX960.(First,set on wifi module, then, during sleep mode, change wifi module to m.2-mPCI adapter.) Then, next, Error12 occured. That's why I ask you about"Setup 1.3". What I want to ask is: 1. in the following URL, there is a person who has quite similar problem http://forum.techinferno.com/<wbr>diy-e-gpu-projects/2123-diy-<wbr>egpu-setup-1-30-previously-<wbr>setup-1-x-2.html The article no. is #12 Do the set-up procedure, right clicking "setup-disk-image" and selecting "Run as administrator" , then below massage shows. ------------------------------<wbr>------------------------------<wbr>-from here ******************************<wbr>******************** BIG WARNING!! mkdevcon: PCI BUS section NOT found ******************************<wbr>******************** If you are using a non-English language, then please edit the following: v:\config\devcon.txt and remove the "PCI BUS" section that will be in another language. Otherwise the addresses referred to in that section will be such that the the complete PCI BUS will be excluded during compact and compaction will find no solutions(fail). ------------------------------<wbr>------------------------------<wbr>-----------------------end http://forum.techinferno.com/<wbr>diy-e-gpu-projects/5096-egpu-<wbr>dell-studio-1747-not-working-<wbr>easily.html This URL also includes similar situation. Though I already deleted "ACPI\PNP0A08\0 ･･････ IO : 0d00-ffff " codes, the problem still exists. In addition to that, I don't know this action is right or not. This is first problem. 2. Second is the fatal point. Your guidance : "Rebooting will now show a "Setup 1.x" bootitem in the Win7/8 (or XP if still using it) bootmenu. Select Setup 1.x then Setup 1.30-menu-based" Reboot, and "Setup 1.3" shows, then select "3. DIY eGPU Setup 1.30 : menu-based" This massage shows. What 'iport functionality disabled for now' means? Why "disabled now"? Then, entering 'setup' or pressing F10 results in following picture. Of course, this picture is after pressing F1. Then, I do not understand what I have to do, I ran No.1 "iport scan". So, following codes show. I can't understand this massage, but I've done all I could do. Below two photos show what I did.(I ran two compaction menu, but PC freezed on 1h) Your reply in this thread,"Looks like you have found a bug on the AMD platform where the refresh (F5) drops out to DOS. A workaround for the time being is simply type 'setup' or hit F10 to return to the menus. Then proceed to highlight PCI compaction->Run compact and hit F1." But, I can't find "highlight PCI compaction->Run compact" at all. Whare is the menu? What can I do? I do want to get through this situation. So please help me! My English is poor, so please ask me when you read my article and find something wrong. Regards.