Jump to content
EwinRacing Flash Series Gaming Chairs
Sign in to follow this  
Doki

[Hardware Mod] better cooling for p170hm

Recommended Posts

Hello everone,

 

i just want to share you some Hardware mod ideas for the p170hm.

the goal was to improve the airflow for the fans, while maintaining a decent look of the notebook case.

 

overall improvements:

GPU (GTX680M OC) about 7°C drop at 100% load

CPU (i7 2820QM) about 6° drop at 100% load

 

not sure if the two small fans helping that much. you guys think its better if they would suck in the cold air instead of blowing hot air out?

 

the fans are 30x30x7mm. the power is taken from the sata connector.

 

this took me about 3 hours to make.

 

 

IMAG0424.jpg

IMAG0425.jpg

IMAG0426.jpg

IMAG0427.jpg

IMAG0428.jpg

IMAG0429.jpg

IMAG0431.jpg

IMAG0432.jpg

IMAG0433.jpg

Share this post


Link to post
Share on other sites

Those small fans likely help the CPU a little, but probably not the GPU. Are those fans from a Dell Inspiron 8000/8100/8200? I would definitely have them suck air in.

 

The mod that helped you the most was widening the fan air intakes. They are way too small on Clevo systems until the ZM series laptops.

Edited by Khenglish

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Content

    • By laxus
      i want to ask two favours and a question from this community ..
       
      1.) Can someone mod my 940 mx to increase the target temperature and allow higher overclocking than 135hzband voltage control
       
      2.) Allowing my i5 7200U to be undervolted to reduce overall heat 
       
      The question : I repasted my gpu and cpu cleaned it thoroughly, made sure twice everything is connected properly, use a cooling pad and yet the upper portion of my chasis above f1-f12 keys is so hot that i can roast peanuts on it. 
       
      (if i left out any info or missed something please reply i would really love to have a page that has everything for people who have this laptop specifically for light gaming.)
    • By TheFlameParadox
      Hi everyone,
      i'm writing this post to ask you if someone is interested about making for me an overclocked gpu vbios.
      I have a Dell M6700 with a NVIDIA K3000M and i' m kinda good with it but i m searching about getting more performance from it.
      So basically i want to have a 850 Mhz OC vbios rom and a 950 Mhz OC vbios rom, is there anyone that can do this for me please ?
      I tried using kepler vbios tweaker but i remains stuck at 548.9 Mhz without going up and i can t figure how to do it.
      I'll attach my VBIOS BACKUP CLEAR COPY.
       
      PS: Tech Inferno seems to have upload problems now so if you want the rom image contact me pls asap
    • By Awesome14
      Over the last 10 years I've found laptops throttle the processor speed in order to keep fan noise down. I prefer the fan to run noisily, and the processor to run at full speed. I've developed tried and true mods for lappies and have demonstrated their effectiveness.
       
      I have two Lenovo W541 laptop workstations with I7-4940MX processors and discrete nVidia graphics. On one I overhauled the cooling. Copper shim between CPU and hsf, AS5 on both sides. Shims between hsf and inductors near CPU and gpu, and shim on the gpu.
       
      Used 'thinkpad_acpi' Linux kernel module to set fan to max speed. Ran mprime (prime95 for Linux) AND Unigine Heaven, alternating,  to cure the AS5. Then ran mprime. Temps were slightly high. But laptop processors tend to run hot. 
       
      The I7-4940MX is a 3.1 GHz, 4.0GHz. Turbo processor. The modded machine ran at 3GHz. continuously running mprime, for weeks. The unmodded machine with the same max-fan-speed software tweak and stock thermal-interface material, throttled to 1.7GHz.  at the same running temps.
       
      Clearly, laptop manufacturers are robbing performance off the top, by inferior cooling hardware and materials. Granted, getting the cooling mod to all fit together correctly with smooth, flat surfaces requires hours of work and materials not normally found sitting around the house.
       
      I normally do not mod the CPU die. I abrade copper surfaces down to 1500 grit paper, and then polish with scapings from a bar of buffing compound. Everything is done on 1/2" plate glass to maintain flatness. The final mirror polish is done with the compound granules on a clean, damp cloth.
       
      Desktop processors mostly have slightly raised corners, so smoothness is not as much of concern. You're going to get thermal-interface compond completely covering the center of the processor. The ideal is to fill the microscopic gaps between the cpu die and the hsf, but where there is metal on metal, have it be. 
       
      Metal to metal provides 100s to 1,000s times the heat transfer of thermal paste. But, on a desktop, there are more effective cooling solutions than moving air. Most user are satisfied with their laptops, because the processor doesn't run full speed long enough to make a difference.
       
      But I enjoy tweaking, and I do processor-intensive work, like batch editing 100s of large images, video rendering, security testing, password recovery, network testing; that are all severely compromised by poor, stock laptop cooling solutions.
    • By Henrik9979
      First I want to thank the community, who have inspired me to do this project.
      I will give you guys the chance to follow me on this journey.
       
      I hope you will all help me come up with ideas, techniques and parts that could become handy.
       
      This modding may be possible to convert to allot of laptops.
       
      Let's begin!
      Here is the measurement of the went hole.
      77mm X 16mm

       
      I have 2 ideas for what can be done.
       
    • By BlazingBrandon
      I own a Clevo P151SM1 that I bought in a hurry last year after my Alienware died on me. It's done a good job of playing everything I've thrown at it but lately, it's been shutting itself off when I play certain games or graphics-heavy programs. When idle it sits around 38C which is great. But when I get into a game it skyrockets up to 97C as the last recorded temp before it shuts itself off. I've cleaned the fans and keep it on an elevated cooling pad (no fans on the pad cause I broke them) but it gets plenty of air. I know that 97C is probably damaging the card and I don't want that. Does it look like I'm going to have to repaste it?  I've attached my latest readings if that would help. 
      HWMonitor.rar
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.