Hello Fellow Tech Gurus!
I am having a huge headache after upgrading the ram memory of my m17x r3.
First let me start by saying I have been experiencing issues with my current ram setup recently, and so i decided to replace the ram inside of my computer, thinking they had gone out on me. It originally came with x4 2gb memory sticks, and as I started to experience issue, I started to removed them, and I was down to 1 2gb stick. It seems to me ram slots 1 & 2 are not working properly as when I put ram memory into them I would get BSOD in 5-10 mins of computer usage after boot. So I am thinking the slots have gone out. I also tested each slot individually and still same effect.
So I went on the try out slots 3 & 4 under the keyboard, which seems to work just fine when I use only 1 ram chip in one or the other. But the problem occurs when I try and fill both ram slots in slots 3 & 4 under the keyboard with crucial 2x 8 gb of ram sticks, which total to 16gb total ram memory.
BSOD and freezing occurs like crazy. But if I use just one of the ram sticks in either slot, no problem.
I dunno if this is hardware or software. I am think that my motherboard is on its way out the door, but any suggestions you all have would be great. I have already clean installed win 7, and is currently running bios A10 (unlocked, I believe)
I would also like to note that my motherboards internal vga is not detected, and just noticed this a few days ago upon trying to figure out the ram situation.
other issues is my laptop battery is pretty much dead, and the only for my computer to cut on is if the AC adapter is connected
I would also like to know can 1x 16gb 1600 ram stick run in my computer? or is it not supported by my motherboard?
Alienware M17xR3 (2011 3D FHD ed)
A10 (should be unlocked)
Microsoft Windows 7 Home Premium (64-bit)
Intel® Core™ i7-2960XM CPU @ 2.70GHz
Intel® 6 Series/C200 Series Chipset Family
Nvidia GTX 680m
IDT High Definition Audio CODEC
High Definition Audio Device
Networking and I/O
DW1501 Wireless-N WLAN Half-Mini Card
Atheros AR8151 PCI-E Gigabit Ethernet Controller (NDIS 6.20)
HMA TAP-Windows Adapter V9
Crucial 8 GB (x2 qty) DDR3 PC3-12800 • CL=11 • Unbuffered • NON-ECC • DDR3-1600 • 1.35V • 1024Meg x 64 •
(these only work under bay 3 or 4, but not dual 8gb at the same time, otherwise BSOD)
WDC WDBNCE5000PNC SSD (installed into bay 0)
I just got a Dell r9 m290x card for my m17x r3. I'm using the stock A12 BIOS. Had PEG set in the BIOS and on boot had a black screen. I cleared CMOS, most likely reverted back to SG and on boot had a black screen with 8 beeps.
I've seen people on here report that it is working for them. Do I need to use a different vBIOS? Or maybe the unlocked A12 BIOS with some settings changed?
Any help would be appreciated Thanks.
Just like the title says, I cant get the driver to install. I'm on Windows 10 x64 release 160906. The card works in 1920 x 1080 with the windows vga drivers. I've disabled driver signing, I'm in test mode. I've tried the nvidia driver versions, 365.19, 372.54, 372.70, 372.90. With modded inf's for each from laptopvideo2go.com They all start the install, but when it gets to the driver install, the screen goes black for about 30 seconds, then the computer just reboots. The drivers don't get installed. I've seen a bunch of threads around about Windows 8, but nothing that seems to answer for windows 10. Is there something that I'm missing to get the drivers installed?
Update, found this thread.
I got the drivers installed following the directions, but after rebooting back into normal mode, the computer just reboots. I see the windows logo, screen goes black, then after about 30 seconds, it just reboots. This was using the 372.90 and inf files from the thread.
Do someone got solution for GPU fan in M17x r3 after R9 m290x upgrade ???
i use HWinfo but will be nice if someone help me how solve this problem.
I know this its old topic but when i try find somethings about this i got nothing.