I've a really weird problem. My laptop has started beeping when use nvidia gpu yesterday. I dissambled my laptop and tried to plug out every single hardware and test them one by one. There's 22 beeps and equal interval beetween them. It goes shutdown after that 22 beeps.
My laptop is Clevo W650SJ and it uses Nvidia 840M gpu. That problem isn't causing because of windows or installed driver cos i tried to reinstall windows but it started to beeping when w10 installer check devices. Also I've bios password on startup , if i don't type password and hit the enter , it starts beeping after 10-15 sec. Also fan speed goes up to maximum and it doesn't slow down untill i shut it down or shutdown itself.
If i use any program or run a game which uses nvidia gpu , it starts beeping but if i close the game on first beeps , beeping is stops. But fan speed still maxiumum until i shutdown to pc.
I am looking a way to fix it. I didn't make any changes on my pc before than this problem.
When my first CPU fan on Y500 is broke i replaced it on something compatible (non-original) and planned to replace it later on original. Since that time happened a lot things, but i still using that non-original fan. But i did some research and here is what i founded:
1. Forcecon (marked as FCN on fan)
DFS5413005MH0T-FC1C (5V - 0.5A)
Spotted in: Y400, Y500.
2. Asia Vital Components (marked as AVC on fan)
BNTA0612R5H-P007 (5V - 0.5A)
Spotted in: Y410p, Y500, Y510p.
3. Sunon (marked as SUNON MagLev on fan)
MG60120V1-C230-S99 (5V - 2.25W (0.45A))
Spotted in: Y410p, Y500.
So, which to choose? Any recomendation? Maybe there also unexpected way (completely diffirent fan from another company for another laptop)?
I'm debating whether or not to replace the thermal paste in my Lenovo y510p. I've started overclocking a bit, and I have an external fan, but I would like to not have to run the fan as fast because it is a little loud. I have been reading a bit about different thermal pastes, and I'm wondering if there is even a big difference between stock thermal paste, and something like the liquid metal from thermal grizzly. It sounds like it'd work better, but I don't want to fall for a good marketing scheme. If anyone has experience with this and has or hasn't seen big differences, your input would be greatly appreciated.
Thanks in advance!
Hey guys, first post, but I thought I’d discuss my heatsink fan retrofit in my old M14x r1.
Old fan was loud and not very efficient: the air transfer rate was around 2 cfm (I’m assuming cubic feet per minute). Finally had enough and decided to swap out the crappy r1 fan/coughing pinwheel for a r2 fan (rated at 10.4cfm).
I found an old r2 heat sink on eBay (beware though that the heat sink for the r2 will NOT fit the gpu/cpu configuration for the r1. HOWEVER, the fan of the r2 heat sink it is attached to is a carbon copy fit into the r1 MoBo. A few philips head screws and a seal of good electric tape and BAM, you’ve got a significantly cooler and MUCH quieter intake fan in your old R1.
My CPU temps from before were around 87-88 max load in FSX, 65 for the GPU; bear in mind this is after a repaste. Now with the new fan, I’m not going over 77 degrees on the CPU, and the gpu stays around 58, all while being MUCH quiter. I’ll post pics of the walkthrough if anyone is interested.
Just thought I’d share with all you fellow loonies trying to squeeze every last frame and degree out of our “portable toaster ovens with a screen and keyboard”.
I have an XMG u705 with the an í7 4790k, a Geforce GTX 980M 8GB, G-Sync Monitor, 32GB DDR3 RAM, etc. and I am damn annoyed by both the Mainboard Bios and Vbios, because both are the cause for a ton of driver issues under Windows 10. Also I can't use my lately bought Samsung 970 Evo, even though technically there should be nothing preventing it. Heck I was even able to install Windows 10 on it, because the Windows 10 installer detected it, just not the Bios which is logically why I cannot boot from it. -.-
So in search of a solution, I searched the web and found out that there are several mods for both bios made by devs like Prema. Unfortunately some Bios mods I found are heavily outdated, unfinished, ... or not anywhere secure and I couldn't find any location where I could download Prema's Mods for this device, especially not on his Site (just a Subscribe banner there) or his older Wordpress site (errors). There is also nothing here under Downloads/Clevo/P77xZM.
I would be really thankfull if someone could help me.