Jump to content
DaSpaceMonkey

GTX 1060 error 43 EGPU

Recommended Posts

I am using an EGPU on my Lenovo Y510p (http://imgur.com/HN51mJj). I have hooked up the GPU and booted up windows and I got the error 43 message (http://imgur.com/QfhThfh). I a using a Corsair CX600PSU and the V8.0 EXP GDC Beast EGPU enclosure (http://www.banggood.com/Mini-PCI-E-Version-V8_0-EXP-GDC-Beast-Laptop-External-Independent-Video-Card-Dock-p-1011222.html).

Edited by DaSpaceMonkey

Share this post


Link to post
Share on other sites
On 12/28/2016 at 4:14 PM, DaSpaceMonkey said:

I am using an EGPU on my Lenovo Y510p (http://imgur.com/HN51mJj). I have hooked up the GPU and booted up windows and I got the error 43 message (http://imgur.com/QfhThfh). I a using a Corsair CX600PSU and the V8.0 EXP GDC Beast EGPU enclosure (http://www.banggood.com/Mini-PCI-E-Version-V8_0-EXP-GDC-Beast-Laptop-External-Independent-Video-Card-Dock-p-1011222.html).

-

Disable automatic driver installation

uninstall dgpu and egpu drivers

download old nvidia driver ( i used 376.33)

reboot

install old driver

-

egpu should now work, it did for me.

if not, fiddle around by disabling gpus and using different drivers or gdc beast delay.

also, check if the egpu shows an image in BIOS.

Share this post


Link to post
Share on other sites
9 hours ago, ceigyx said:

-

Disable automatic driver installation

uninstall dgpu and egpu drivers

download old nvidia driver ( i used 376.33)

reboot

install old driver

-

egpu should now work, it did for me.

if not, fiddle around by disabling gpus and using different drivers or gdc beast delay.

also, check if the egpu shows an image in BIOS.

Ok I just swapped GPUs with my brother (now I have a GTX 960). And it is working now (with current drivers), I am going to wait till there is a driver fix (if there is going to be one). Thanks for the help. 

Share this post


Link to post
Share on other sites

I had similar issues (even read this thread looking for help) and after a bit of trial and error I managed to sort them out. I'll describe my setup and what I did to resolve the Error Code 43.

Laptop:

Lenovo y510p with Dual Nvidia 755m (SLI)

16GB RAM

SATA SSD and NGFF SSD

Windows 10

I have recently bought the EXP GDC Beast Laptop External Independent Video Card Dock + Mini PCI-E Cable   WITH POWER ADAPTER along with a Zotac 1060 6GB AMP card.

The supplied PSU outputs 220w of which the Zotac 1060 requires 140w.

 

Before you begin - make sure you uninstall the Nvidia Laptop drivers completely

Remove Ultra Bay GFX if you have it (Should be removed by this point to get to the WiFi card)

Disable 755M & Intel 4600 GFX adaptors in Device Manager

Download and install - 368.81-desktop-win10-64bit-international-whql

Connect HDMI cable to external GFX card (critical step this one...)

 

My set up is working perfectly and is stable. I did try to go back to the 372.xx drivers and nothing worked so I went back further to 368.81

 

I hope this helps.

 

Device Manager.PNG

Edited by Contact
adding photo
  • Thumbs Up 1

Share this post


Link to post
Share on other sites
2 hours ago, Contact said:

I had similar issues (even read this thread looking for help) and after a bit of trial and error I managed to sort them out. I'll describe my setup and what I did to resolve the Error Code 43.

Laptop:

Lenovo y510p with Dual Nvidia 755m (SLI)

16GB RAM

SATA SSD and NGFF SSD

Windows 10

I have recently bought the EXP GDC Beast Laptop External Independent Video Card Dock + Mini PCI-E Cable   WITH POWER ADAPTER along with a Zotac 1060 6GB AMP card.

The supplied PSU outputs 220w of which the Zotac 1060 requires 140w.

 

Before you begin - make sure you uninstall the Nvidia Laptop drivers completely

Remove Ultra Bay GFX if you have it (Should be removed by this point to get to the WiFi card)

Disable 755M & Intel 4600 GFX adaptors in Device Manager

Download and install - 368.81-desktop-win10-64bit-international-whql

Connect HDMI cable to external GFX card (critical step this one...)

 

My set up is working perfectly and is stable. I did try to go back to the 372.xx drivers and nothing worked so I went back further to 368.81

 

I hope this helps.

 

Device Manager.PNG

I was trying to install the 368.81 desktop drivers after disabling 755m and Intel graphics and got an error. It said that it couldn't find the compatable graphics hardware. What should I do?Ae55bYG.jpg

Share this post


Link to post
Share on other sites

Hi,

 

Check to see if your eGPU is being detected in Device Manager as I had that issue when I rebooted and it stopped seeing my card.

Press F2 on reboot and go into the BIOS  - Check what your Graphics settings are - What are your Graphics set to?

Exit out and then boot into Windows normally and see if your external card is being detected in Device Manager. 

 

Make sure that you are downloading drivers for the Desktop Nvidia cards and not the Laptop ones.

Share this post


Link to post
Share on other sites

Thanks for the reply @Contact it is set to UMA only and it is in Device Manager under microsolft basic display adapter or whatever. It's been in deceted Device Manager before and yes I am using the desktop drivers. 

Share this post


Link to post
Share on other sites

Try taking it off UMA only - mine isn't on that setting.

Share this post


Link to post
Share on other sites

I enabled the 755m in the BIOS, then disabled it in windows. ASO1wVP.jpg

 

So then I tried installing the 368.81 DESKTOP drivers and all it did was re-enable the 755m. icq72MB.jpg

Share this post


Link to post
Share on other sites

That is pretty strange...

Has your device manager ever identified the eGPU as a 1060 or has it always come up as the Microsoft Basic Display Adaptor?

 

If it hasn't ever been identified as the 1060 then there could possibly be an issue with one or maybe more of the below:

1) 1060 Graphics card

2) eGPU Adaptor (Cable not seated properly or faulty unit)

3) Power Supply Unit  (faulty rail or not supplying enough amps on the rail)

 

Easiest way to check the this would be to:

1) Try a different external graphics card (borrow one from a friend etc.)

2) Connect your current setup to another laptop

 

It is essential that Windows identifies the eGPU as the 1060 (or whatever card you have inserted) otherwise the drivers won't install.

 

 

Share this post


Link to post
Share on other sites
19 hours ago, Contact said:

That is pretty strange...

Has your device manager ever identified the eGPU as a 1060 or has it always come up as the Microsoft Basic Display Adaptor?

 

If it hasn't ever been identified as the 1060 then there could possibly be an issue with one or maybe more of the below:

1) 1060 Graphics card

2) eGPU Adaptor (Cable not seated properly or faulty unit)

3) Power Supply Unit  (faulty rail or not supplying enough amps on the rail)

 

Easiest way to check the this would be to:

1) Try a different external graphics card (borrow one from a friend etc.)

2) Connect your current setup to another laptop

 

It is essential that Windows identifies the eGPU as the 1060 (or whatever card you have inserted) otherwise the drivers won't install.

 

 

I also have this problem the only difference is my asus laptop just cant tottaly detect my egpu you are lucky for microsoft basic display adaptor to show up.. you just have to mod/edit the nvami.inf inside the nvidia folder(nvami.inf is for asus) for other brands there is other name... im still hoping for my gtx 1070 to show up at my device manager

Share this post


Link to post
Share on other sites

Hello!

 

My configuration is MSI GT70 (i7-4700, 32Gb, 970M)

Got the same error 43. Resolve after disable in System Device PCI-Express x16 Controller - where lived dGPU (970M). After that all is ok!

 

 

Error_43_2.jpg

Edited by user7780

Share this post


Link to post
Share on other sites

hi guys 

 

i have a same problem i try to run asus strix GTX 1080 to my lenovo laptop y510p and GDC V 8.0.

i see a gpu but there is code 43 error.

 

plz tell me the solution...

Share this post


Link to post
Share on other sites

hi

 

i have same problem ... my egpu is msi gaming x 1060 and my laptop is asus x450ld 

i did all of thoes but still nothing hpend just shows the NVIDIA GeforceGTX 1060 6GB in the device manager with a yellow mark and error 43 

plz help me to fix it

 

http://uupload.ir/files/xps_1551383510455-934387929.jpg

 

Edited by omiiid1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By SnipeKing17
      The GPU works, The PSU works, The system works. [individually they all do work]
       
      The system works perfectly fine without the WLAN card.
       
      When i put the system to sleep and hotswap the mPCIe riser and WLAN press something on the keyboard.. Restarts.
      Will shutdown in roughly 27 seconds for those 27 seconds it works just fine like how it normally would on external monitor.
       
      When i shut it down and plug the riser and switch it on, same story. 27 seconds.
       
      I don't even see a error. I get to login screen directly. I used DDU already.
       
      I timed it. no matter what i do if i use the eGPU, External monitor it restarts instead of pause-play. I have 27 seconds.
       
      Need help!
    • By picardilly
      Hey guys, I am Grga and i am new here. I rarely use forums but i am desperate in this case.
      So, as i have seen many of you have had the issue with obsolete BIOS versions for clevo P7xxZM machines,
      So i would like to hear your experiences and how you went about it. 
      I have recently bought an ssd Samsung 970 PRO NVMe M.2. From which i would like to boot the windows10.
      Little did i know that there was no support for that kind of protocol in the BIOS or that there is such thing as UEFI (for which i am still not sure what that is exactly, except some kind of successor of BIOS).
      So i did a bit of research and updated my Bios and ec to 1.03.15 and 1.03.09 respectively for which i understand is the last available official release. I changed to uefi mode with secure boot disabled etc... in short i did everything that my (limited) knowledge about these things allowed me to do (and the sweat of excitement and fear when i was flashing the bios for the first time in my life). But, alas, it all yielded no success,  and now i am lost. I have really no idea what to do, and whom to ask for help except for you guys here. The only thing that i understand worked for some of you is when you mentioned a wizard named @Prema so therefore i will try to do the same....
    • By Kel
      I got the exp gdc beast 8.5 got all the connections right... laptop boots up... fans turn on the gpu.... device manager detects gtx 1060 with a “ ! “ in a yellow triangle. Now what to do.... i tried to do the bios mod.... but realised that i have 3.07 version. 
      Questions-
      1 is there any way to get this done without the mod?? 
      2 if mod is the only way... kindly help me with step by step instruction in laymans terms... i m not a techy... so i might not understand technical terms.... altho i am interested... but learning yet. Please help. 
    • By Drozof
      Has any company out there launched a laptop with an external MXM port? 
       
      Just curious since with the boom in the gaming laptop market and some companies launching eGPU thunderbolt enclosures, isnt the MXM faster?
       
      Is it because of licensing issues? or hardware problems?
       
    • By Iwillsolo
      Hello guys ...

      i wanna make sure that everything is going to work fine with my laptop so i got some questions

      First of all my laptop is Lenovo Z51-70
      CPU: I5-5200U 2.2ghz
      iGPU Intel HD 5500
      dGPU:AMD R9 M375
      Ram: 8GB (will raise it to 16GB)
      HDD: 1TB stock one
      SSD: 120GB (for my games and windows only)

      now i investigated  a little about eGPUs and found that i need a M.2 or thunderbolt, i've found that my wifi card use a M.2 a/e key aka ngff, so i will be using the GDC Beast NGFF version

      to the bad part / question part

      What do i need to know other than the stuff above?
      what is the white-listing thing? i found on support forums that my laptop support some wifi cards only and it's bios cann't be modified according to bios modifying forums (not here)
      in same time saw some posts on reddit that says if ur bios have UMA graphic option then you will need to disable PAX / WIRELESS and enable UMA and it will work fine, the question is that true?

      i wasn't able to find anyone who did it on Z51-70 i found only 1 post on reddit for Z41-70 (which after research found that both are using same M.2 a/e key slot and also same bios... but the one who posted only replied that it's recognized with some errors and never replied back with any updates so still not sure about it.....

       
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.