Jump to content
EwinRacing Flash Series Gaming Chairs
  • [Alienware] Aftermarket Upgrades Driver Support - Modded INF


    J95

    Instructions for modifying the latest GeForce 361.91 WHQL driver inf to work with Alienware notebooks.

     

    GeForce 361.91 WHQL


        *Install drivers at your own risk* Windows 10 + GeForce Drivers are Killing Samsung and LG Notebook LCD Display Panels
          Uninstall both PrecisionX & MSI Afterburner (Keep RTSS) including screen overclocking tools *Still at risk*

     

           Requirements:

           Due to driver incompatibility (black screens, TDRs, BSODs...) with previous vBIOS versions you must flash latest @Prema's v2 980M & 970M (Please consider donating to Prema)


    • Win10/8.1 'F8' Boot options 'Safe Mode' & 'Disable driver Signing'
      cmd (Admin)
    bcdedit /set {default} bootmenupolicy legacy

     

            -> reboot -> F8 -> select 'Disable Driver Signature Enforcement' -> Install drivers

    • Run DDU "Clean & Shutdown (Safe Mode)
    • Extract driver using 7-Zip
    • Display.Driver folder,  copy/overwrite the proper .inf file
    • Extracted driver package,  run setup.exe  

           -> Keep these folders only <-

    361.75.thumb.PNG.cd5111f39779e9d64f24d39

     

     

        INF MOD v361.91

       

    nv_dispi.inf (including nvdmi.inf) PEG/Dedicated All Models: M15x, M17x, AW17 R1, M18x, AW18 R1 (including Optimus/M17xR4) excluding AW 2015 - GTX 980M , 970M , 965M , 880M , 870M , 860M , 780M , 770M , 765M , 680M , 675MX , 670MX , 660M

     

    nvcvi.inf: Optimus Alienware 17 / 05AA (only) GTX 980M - 970M - 965M

          

    Updated throttle free PEG MODs

     

    GeForce 353.00 PEG MOD Win7/8.1 - Full_Profiles_8_v353.00.txt

     

    GeForce 352.84 PEG MOD Win 10 - Full_Profiles_4_v352.84.txt...soon Done!

     

     

     

    GeForce 361.91 Win 7/8.1

    GeForce 361.91 Win10

     

     

    nv_dispi.inf_v361.91_Win7_8.1_PEG_Dedicated.zip

    nvcvi.inf_v361.91_Win7_8.1_Optimus_Alienware_17.zip

     

    nv_dispi.inf_v361.91_Win10_PEG_Dedicated.zip

    nvcvi.inf_v361.91_Win10_Optimus_Alienware_17.zip

     

     

    @thegh0sts

    120Hz models! NV v361.75 previously installed, set refresh rate to 60Hz before uninstalling drivers. DDU uninstall "Clean and restart",  Options: uncheck "Remove present and non-present monitors"

     

    DDU2.thumb.PNG.4070f614da472125a2264c0cf

     

    Continue original discussion here. 


      Report Article


    User Feedback


    I removed my previous intel drivers in safe mode using ddu. I was running peg with no Intel driver installed at all. After reboot windows comes to black screen and the restore point didn't save with previous working drivers. I am trying to see what's possible as I somehow need to install the drivers in safe mode but without signature verification and I'm not sure if that's possible. I'm guessing maybe installing Intel driver in safe mode may let me boot to start over again though I wanted to avoid that. Windows is also set to neverase update video drivers in Windows 10 as per DDU. Any ideas other than what I stated above? 

    Share this comment


    Link to comment
    Share on other sites


    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Add a comment...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By Crustieraxe
      Hello Guys this is my first post here!
       
      So my original post was this:
       
      "I don't even know if any active forum is out there on this laptop and on this issue, but after installing my new DHCG2 LTN173HT02 120hz display, I am unable to boot up on it. I do have a modded bios which the video setting is set to PEG, and just about read every forum about this but have not found a solution. I have tried resetting the bios, made sure the cable is plugged into the Edp port, and have made sure I have an UFEI Windows installation and legacy mode is turned off. I don't know what else to do and if anyone could help it would mean alot to me! "
       
      The reason it was not booting up on a pure UEFI environment is because my 660m did not have the GOP compliant driver vbios. You would need this in order to boot up in a pure UEFI environment which at the time I didn't know, and my fix was to stick to legacy. Any card before the 660m will most likely require this if you need to boot up in a pure UEFI environment. If you do not have this vbios driver while it is set to UEFI and plug in the 120hz lcd, it will beep 8 times and you will be forced to plug back in the 60hz display to change it back to legacy.
       
      This was the vbios that I can say worked for me and had the GOP compliant driver for the 660m
       
      https://www.techpowerup.com/vgabios/144032/144032
       
      ------------------------------------------------------------------
       
      These are the steps to upgrade from a normal 1600x900 60hz display to a 1920x1080 3D 120hz Display which is needed if you want to update your graphics card to a more modern one.
       
      I am making this guide because I felt frustrated that for this awesome computer, there aren't really any post in 2020 to upgrade the LCD panel to the 3D 120hz one. And The older posts I scavaged through really helped me little in doing this upgrade.
       
      Anyways lets begin
       
       
      1) If you have a stock amd graphics card, and are wanting to install the 120hz display, then your journey ends here and you will have to upgrade to an nvida graphics card to do so. If you have an nvida graphics card, you may continue
       
      2) On the 60hz display, I would start by firstly making sure that you have windows 10 installed or reinstall with UEFI support, or search up how to convert a current installation of windows to UEFI
      if you are installing a pascal graphics card. If you have legacy mode enabled, and are not planning to upgrade to a pascal graphics card, then disregard this and head on to step 5 (although I would recommend to read everything)
       
      3) turn the laptop off and boot into the bios. In order to boot into the bios, spam the F2 key while it is turning on.
       
      4) Once in the bios, go to the Boot menu, and make sure to Disable "Secure Boot", Make sure that importantly if you converted over to a UEFI installation of windows, UEFI mode is chosen (UEFI  Environment will be needed for a pascal graphic card and legacy will not be compatible) then again, if you are on a legacy installation of windows, disregard this if you don't want to upgrade to a pascal graphics card.
       
      5) we can now start looking at the 120hz display. I bought mine on ebay with this seller https://www.ebay.com/itm/New-Dell-Alienware-M17X-R4-17-3-FHD-WLED-3D-V-M-LCD-Screen-DP-N-DHCG2-GN36T/273644412867?hash=item3fb67a5fc3:g:9A0AAOSw5AhcP1pw:sc:USPSPriority!32720!US!-1 (Just in case the link goes bad, this was the listing name"Alienware M17X R4 17.3" FHD WLED 3D V M LCD Screen DP/N DHCG2 GN36T"  with the screen model being  LTN173HT02 and Dell part number GN36T )
       
      6) Since my listing came with the video cables, I did not have to go out and look for the video cable. If yours did not come with the cables, You will also NEED to get the video cable it is required. the Dell Part number is N392W. I cannot stress enough This video cable is required and the 60hz's video cable CANNOT be used with the 120hz one or else you will brick your computer from what I read.
       
      7) Once it comes In, we can start to take apart the computer to Install our new display. I watched this video to remove the old 60hz and install the 120hz panel 
       
       
       
      8) Before I would remove the whole 60hz lcd panel, I would first make sure that you can boot on the 120hz panel. Notice that there is one connecter with screws on both sides right next to where the 60hz screen connecter is. Make sure that you put the 120hz one with the connector where screws are. This is known as the Edp port and cannot be confused with the LVDS port. Again, you want to plug the new 120hz display into the EDP port and unplug the 60hz one.
       
      9) If parts 2-3 where completed correctly, then you should have no problem booting with the screen. if it is giving you 8 beeps, then just plug in the 60hz display, and navigate back to the bios to make sure everything is in order and refer back to steps 2-3. If you happen to be an advanced user like me and went ahead and installed a modded bios, then on the 60hz display make sure that the video setting is set to PEG. I dont think this is necessary to have a modded bios since the bios automatically changes the video setting when the 120hz display is detected and should be a last resort option to install a modded bios. I got my modded A12 bios from a guy in this forum named klem for 10 US dollars thorough paypal ( all you have to do is go to page 32 and @ him and he will send you a pm. Just know that this is not necessary. 
       
       
      10) Once the new LCD is tested and you know you can boot up with no problems, go ahead and finish removing the old 60hz LCD and proceed to finish installing the 120hz LCD. And you are done. 
       
      A couple of words from my personal experience: When I installed the 120hz display, and booted up windows on it, and turned the computer off, it refused to turn on for some weird reason. I don't know why it would turn on when the AC and battery where on. regardless of what this was, I fixed it by Reseting the CMOS. If you don't know how to do this, do a quick google search and after turning it on i got 5 beeps which i then turned the computer off, and then turned it back on which the computer just reset itself and when it turned back on I was able to boot up into windows.
       
      I also read an intresting post  where you could upgrade to the 1060 on this computer which is what I eventually want to and for whoever wants to they need to have the 120hz display. As a side note, I did this with the stock 660m that the system originally came with. What i mean with this is that I'm not sure if this procedure works with other graphic cards. Although I suspect that it has. since to upgrade your graphics card, the 120hz LCD needs to be setup
       
      This is the forum that I was able to find about upgrading the graphics card to the 1060.
       
      Anyways I hope I at least helped someone transform their computer! In 2020!
       
       
    • By ajdrenter
      Hello all! I have been researching upgrade paths for my M17x R4 and I have decided on the GTX 1060. Now, I was given this laptop with a dead GPU, and I had an M17x R3 already. So I moved the GTX 560m into the R4 which has worked fine. Now as I understand it a few things are needed for this upgrade including the 120hz panel and the ability to disable the legacy ROM for a pure UEFI boot. I have the 120hz screen, but the 560m uses the GF116 architecture which does not have a vBIOS which supports GOP. So I am thinking the only solution is to buy a cheaper "in-between" card which supports both boot modes, which will allow me to disable the legacy option in setup. Does anyone have any suggestions as to what cheap card to buy as a transitional part? I have been considering a 765m but I am also wondering if there are any other good choices.
    • By lilkuz2005
      hello all, i just got a gtx 980m from a seller on amazon. i have the card installed in my alienware m17x r4, i have updated the bios to A15 stock, in the bios its showing the card is there, in windows 10 the card is also shown in device manager, but it has the code 43 error, i have disabled driver signing and installed a modded driver but its not working, i have uefi legacy mode enabled, i need help getting this working, do i need a modded bios to get the card working? is my card a g-sync version ? any help with this would be great, also if it is a g-sync card, can i vbios flash it with a non g-sync vbios? how can i tell if this card is a clevo or msi ? thanks in advance
    • By depmixels
      hello everyone, I have a MSI GT683R with a dying (pretty much dead actually) GTX560M in it.
       
      I am looking to upgrade it to a new GPU, I have found a AMD Firepro M6100. (I first wanted to upgrade to a GTX970M, but that's too expensive for now... and corona is also making things difficult) I have already ordered a second heatsink to modify because I didn't want to modify the original heatsink it came with.
       
      But, my question is. Does it even work in this system? I have heard of people getting it to work in the barebone variant of this system. But I am not sure if it would work in the 'fully loaded' variant.
       
      Also, my games are mostly RAM/CPU dependent and I am looking for a little extra power in this system. I have found a I7-2860qm and I want to upgrade to 32GB of RAM, is it possible on this system? the sticker says 'max. 16GB of RAM' But I have feeling it says that due to the limitation of the cpu that's already on this system (I7-2630QM, 16GB RAM max.)
    • By Brian
      Following the release of NVIDIAs new 436.02 driver which I mentioned in an earlier article here, I've decided to make a quick and dirty video showing off NVIDIAs new Sharpen filter which is part of their Game Filter feature. It works with the most popular APIs including DX 9, 11, 12 and Vulkan and can be set on a per-game basis with granular settings of 0-100 unlike AMDs RIS which is limited to Navi and lacks DX 11 support.
       
       

      View full article
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.