Jump to content
EwinRacing Flash Series Gaming Chairs
Sign in to follow this  
svl7

Adding AMD 6970m to the Alienware M15x

Recommended Posts

IMPORTANT: The 6970m is not officially supported by Dell. Upgrading to this card may void your warranty. The 6970m is a powerful card, it will draw more power and produce more heat. This card can significantly improve the performance of your system, however, the long-term effects of running this card in a M15x are currently unknown, but it works great so far.

 

Cards that are known to work:

 

  • The card Dell uses in the M17x R3: This has only been tested for a short while so far, but it seems to work perfectly fine. Credits go to Rogue-OP and iloveb00bs, the first guys who tried to put a 6970m in a M15x.

 

-DP/HDMI works, confirmed by Strigae, fan control works
It seems you need to install the M17x R3 drivers first before you can get the official AMD drivers. I guess installing for example the modded 11.4 will work as well.


Dell Part nr. is: V9XKH.Good luck when ordering one from Dell, depending on where you live and what kind of rep you get on the phone they might not want to sell you the card as it isn’t officially available for your system. Call again in this case, or if you know someone with a M17x R3 let him order the card for you.

 

  • 6970m from MXM-upgrade.com: Works great, but no fan control. The fans are constantly at a high speed, but not completely at full full speed. For now you’ll need to manually control the fans with HWinfo32.

 

-DP/HDMI works. Sound through HDMI works when you install the Dell 6970m vbios and the M17x R3 HDMI audio driver. Here are the instructions for this. Card can now be ordered for the M15x from mxm-upgrade.

 

  • Clevo (and resellers) 6970m: The card from Clevo and resellers (Eurocom etc.) works as well, but  make sure you get a version of the card which has holes for the back plate! Some of these cards have the screw holes for mounting the heatsink soldered on which makes it impossible to use the Dell backplate, and since Clevo uses slightly smaller screws than Dell you can’t simply put your heatsink on such a card. Contact your dealer in advance to make sure you get a card which doesn’t have the screw holes soldered to the PCB, otherwise you’ll have to remove it (which is difficult) or use some smaller screws on the heatsink.

 

For all these cards the heatsink of the M15x fits perfectly. No modification needed.

Cards from other vendors / manufacturers may work as well. If you got a different 6970m running in your M15x let me know and I’ll upgrade the list.

 

Things to do before swapping the cards:

 

  • Download the drivers. This modded 11.5 should work, click on “MobilityMod Windows 7/Vista” in the linked thread.
  • Also get GPU-Z for monitoring your video card and verifying it, Trixx, for under- and overclocking and in case you haven’t got a Dell card also HWinfo32 (I recommend getting it anyway since it is a great system monitoring tool)
  • Make sure you have thermal paste, maybe some new thermal pads as well as something to clean the heatsink (e.g. isoproply alcohol) and some cloths around.  I also highly recommend using a grounded ESD-mat and a wristband.
  • Know what you’re doing. You need to partially disassemble your machine to get to the GPU. Prepare yourself thoroughly, check out my little guide. In case you need more information, there’s also the M15x service manual, as well as the teardown video. It can be helpful to write down all the steps in advance when you’re doing this for the first time.

 

The upgrading procedure:

  • Uninstall your GPU drivers.
    Make a power drain (Turn off your M15x, remove the power cord and the battery. Then press and hold down the power button (Alienhead) for about 10-20 sec.
    Remove your GPU.
    Clean your heatsink, if necessary replace the thermal pads with new ones.
    Make sure the 6970m has a retention bracket on the back of the GPU. If not take the one from your old GPU and put it there. Also make sure you read the section about the “retention bracket problem”.
    Properly insert your GPU, make sure that it sits properly. Apply the thermal paste, and attach the heatsink.

     

Then (after reassembling your system), boot, install the drivers and reboot. Make sure the fans are running. Open GPU-Z and verify your card and the clocks. It should look more or less like this. Default 3D clocks are 680/900MHz (core/memory) and 150/100MHz when idling. Make sure PowerPlay is enabled in the Catalyst Control Center. Also make sure Stealth Mode is deactivated.


Check your temperatures. Idle temps should be 40-50°C, but this also depends on your ambient temperature . While gaming or doing something similar GPU-intense the system will run significantly hotter, 70-80°C, maybe a bit higher.

 

Note: By lifting the back of your system a bit (for example with a book) you can improve the airflow in the system. This can really help lowering the temps.

 

The back plate problem:
The retention bracket of the 6970m has a different size than the regular M15x cards (260m, 5850m etc.)When your card doesn’t come with this x-plate you need to take the one you have on your old GPU, but this one won’t fit properly. Nevertheless it works, even if it covers some resistors on the back of the card. Make sure you’re not shorting anything. Usually the back plate has an insulating black plastic pad on it, this will work. However, if your x-plate doesn’t have this pad on it, you must cover it with some thin, insulating tape.


Here you can see the problem, in the first picture I marked the are which gets covered by the backplate and in the second picture the highlighted area shows where the plate should be.

retention-problem-small-150x116.jpg.deab

metal-bezel-small-150x112.jpg.cc710a5825

 

The space beneath the card becomes pretty tight, but it works. My advice is contacting your dealer before buying the card and asking whether he can provide the correct x-plate. (In case he tells you that you should use the one from your old card tell him it has a different size.)

 

Power consumption:
The power draw of the card is probably about 75-100W. I run this card together with an i7 920xm in my M15x and it works fine. Nevertheless you need to be careful, as the PSU of the M15x is only rated 150W. When doing some 3dM11 runs with both GPU and CPU overclocked I measured about 160-170W current draw from my system during the combined test. You really need to be careful when running this card, especially when you have an extreme processor (920/940xm). Pushing both GPU and CPU can (and will) bring the PSU to its limits (and above).

Some numbers about the power draw when playing games, everything on stocks:
Black Ops Zombies (everything on max): ~ 130-140W
Portal 2 (everything on max): ~110-125W
Medal of Honor (everything on max) ~140-150W
Crysis 2 (set to “Hardcore) ~ 140-150W

The device I use for measuring the power draw has an accuracy of about ± 10W.

 

Fan control: In case you have a card which makes your fans running at a high speed all the time you will need to use HWinfo32 to automatically (or if you prefer, manually) control the fan speed.
It’s possible to create a fan control look-up table and let HWinfo32 automatically control the fan speed by temperature.

fan-ctrl.thumb.jpg.062a820cacb8514e11680
1. Click on the fan symbol2. Click on “Custom Auto” 3. Choose the temperature sensor diode which you want to use as reference.4. Set the desired speeds/temperatures according to your needs.
Do this for both GPU and CPU, ignore GPU2 fan. I recommend using the hottest GPU diode (usually MemIO).A big thanks to Mumak, the developer of this fantastic tool. Here you can find the official Alienware fan control thread in case you find a bug or need to know more.

Warning: Adjusting the fan speed can be dangerous!! Always keep an eye on your temps and never forget to adjust the values before doing something CPU or GPU intense (in case you control them manually)

 

Possible problems and solutions:

Unable to install drivers.
Solution: Try a different driver. Also contact your vendor, maybe he knows a specific one that works.
Idle clocks are 250/900 instead of 100/150.
Solution: Check your display settings and make sure only your internal notebook monitor is selected. 250/900 are the idle clocks when you’re connected to an external monitor (or when your display settings are got messed up, probably driver related)
The GPU temps are crazy high!
Solution: Repaste. You probably did a bad job with the thermal paste. Also make sure your system is dust-free and that the heatsink sits properly and is making contact (also check the pads where the memory modules touch the heatsink).
While idling the GPU clocks change from 2d to 3d clocks and back all couple of seconds.
Solution: This behaviour can be caused by the M17x r3 6970m driver (A00). Get the latest AMD driver and you should be fine. If you have this problem with a different driver try another driver version.

 

     

    Share this post


    Link to post
    Share on other sites

    Thank you! Always nice to see that people are trying to keep the Alienware m15x alive!

    Share this post


    Link to post
    Share on other sites

    Thanks! It's so nice that some people wanted to share their knowledge and experience to shed some light.

    Share this post


    Link to post
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Reply to this topic...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    Sign in to follow this  

    • Similar Content

      • By Henrik9979
        Okay here is what's going. I have a alienware m18x r1 running an amd 8970m, I wanted to upgrade it to crossfire but I could see a 8970m was more expensive than a r9 m290x
        So I decided to buy a r9 m290x and see if I could make it work in my alienware and also run crossfire.
        Even though many shops refused to sell me one because the didn't think it would work in an alienware m18x r1 only in the r2.
         
        Here is the whole process.
         
        19/08/17 23:15
        No post bios showing when booting, so impossible to enter bios menu, but can boot into windows 10 with no problems.
         
        19/08/17 23:20
        Because I haven't deleted the old AMD 8970m the r9 m290x shows as a 8970m with no problems.
         
        19/08/17 23:34
        First performance test was a success. The r9 m290x changed p-state normally. The gpu fan start spinning normally. But because of no thermal paste, the test lasted 20 seconds because the temperature raised fast.
         
        20/08/17 00:00
        Created a backup of the vbios version
        015.032.000.004.044450
         
        20/08/17 00:10
        Flashed a new clevo vbios version 015.032.000.003.044465
        Caused the card to be corrupted and resulted the 8 beep code.
         
        20/08/17 00:35
        Finally managed to flash the back and return the graphics card to its original state.

        20/08/17 00:50
        Flashed a new dell vbios version 015.046.000.014.045579
        No change in behavior
         
        20/08/17 01:07
        After trying multiple vbios with no luck I finally found one.
        Dell vbios Version 015.041.000.000.044966
        Brings back the post bios screen and I can now enter the bios menu through the r9 m290x.
        Note: This vbios reduce the cards performance from 900 mhz to 850 mhz
         
        20/08/17 01:21
        After more testing I found one that is working with no limits.
        Clevo vbios version
        015.036.000.005.044618
        Brings back the post bios screen and I can now enter the bios menu through the r9 m290x.
        This will be the vbios I will keep at the moment.

        20/08/17 01:56
        I completely uninstalled the previous driver and installed the newest driver. The graphics card is recognized as a 8970m but works normal.

        21/08/17 20:15
        I have inserted my old 8970m in the secondary slot and will start testing crossfire.
         
        21/08/17 21:45
        I have found out that the fan for the secondary fan did not spin. The is a cable that have felt out. I will fix it now.

        21/08/17 22:00
        In my try to test crossfire compatibility, I installed the newest AMD driver 17.7.2 but as soon it installed the driver for the secondary card it caused black screen. Only booting the computer in safe mode brings the screen back.

        21/08/17 23:02
        After many frustrating hours I finally managed to get crossfire working with the r9 m290x as the primary card and my old 8970m as the secondary.
        I have flashed the same vbios on both cards so the r9 m290x shows up I device manager as a 8970m.
         
        I first installed AMD driver version 16.2.1
         
        Then installed AMD driver version 16.6.1 in order to play battlefield

        21/08/17 23:20
        First test run in battlefield 1

        21/08/17 23:40
        Battlefield 1 is flickering bad, this can maybe be solved with a new patch or driver.
        Other games I have tried is working perfect with crossfire on.


        Now what I would like to try is somehow force the r9 m290x driver to be installed and see if it will make it possible to run the latest AMD driver without getting a blackscreen.
         
        I have tried to edit the .inf file like you would do with nvidia but no luck.
        I have also tried to figure out how to edit the device id in the vbios, but I find it too complex.
      • By Klem
        Klem's_vbios_DELL_GTX880M_80.04.F5.00.07_UNLOCKED.rar
        For 8Gb card.
        1. Unlocked Nvidia core limit +135 MHz.
        2. Unlocked core voltage adjustments.
        3. Unlocked Power Limit.
        4. Unlocked Power adjustment by software (for example with Nvidia Inspector).
        5. Increased Power Limit and Power Target.
        6. Enabled some additional tweaks.
         
        If you liked my mod, you can buy me some beer:   https://www.buymeacoffee.com/ekushukovZ
      • By Noxco
        Hello to all can you help me change the graphics card?
        Alienware m17x r4
         i7 3610qm
        quadro k4100m
        display 120hz 3d
        bios a15
        trying to install 980m but not getting 5 or 8 beeps removed the battery and reset the bios. disabled legacy and secure boot in settings windows 10 gpt uefi
        help how to be?
      • By Guardian241
        So I just received a 980m in the post and after installing it I was greeted by multiple system crashes on my Alienware m17xr4 and was unable to install new drivers.

        Is there a step in the intallation process I missed? A bios setting I was supposed to change? The laptop is already set to UEFI mode in preperation for this and upon putting the old 680m back in the system it now works again. I have heard that I need to change INI files to install drivers but I expected it to at least function without large bugs such as these. Do you think that this GPU is faulty or have I done something wrong?
         
        Thanks for any help you can give.
         
        - M
    ×
    ×
    • Create New...

    Important Information

    By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.