Jump to content

880m cooling / vbios


moaker

Recommended Posts

I dont know if this is the right forum to post this,  (but i need 5 posts for downloading a  vbios)

 

so my questions are these, thank you in advance for reading

 

I have bought a laptop with a half melted 880M GPU Im assuming the person did not keep an eye on temps,

so i went and replaced the card, it runs fine, (alright) but still, I remember modding my VBIOS for my 680 GTX back in the day, and it was fine, exceptionally faster, 

and im looking for that 60 fps LOCK, like i got on my 680 after modding the vbios, 

 

I did increase the voltage on the card to 1.212 I believe, from 1.114 , :P

 

anyway I considering modding the cooling system as well for this laptop, because it definitely lacks cooling 

My plan is to put another laptop fan (where the HDD1 bay is in the Alienware 17) bcause I removed that hdd it was constantly at 57c which is bad

even think it suffered some damage as speeds on it for specific games and tasks are pretty long, and it stays at 100% some times, which is weird, but it still works, so im using it.lol

 

, but in the meantime, I turned the laptop upside down, plugged in the HDMI cable, and now im blasting a ROOM fan at it, which is definitely helping with temps

before I would try to throttle the gpu speed at 77C, or 73C depending on the game or even saying screw it, I dont want throttling, and putting the throttle point to 83C,

I use SPEEDFAN , and it helps keep the laptop relativly cool, except when the gpu is under full load,  putting my hand on it is ridiculously hot, so, with the fan on it, its not going above 70,

and taking a LONG time to get up there, 

i am playing metro last light at around 60C at 60+ fps, where as before my temps were shooting upto 80 and it would hit the throttle point, so  seeing as how this is a 120 HZ laptop, I rather not push it, since the card is not capable (and if it is, the cooling sure isnt)

 

the plan is to put the fan inside the HDD1 bay, and POSSIBLY  daisey chain it to either A) the cpu fan header, or  B ) the gpu fan hjeader, 

 

QUESTION:

not sure which "rails" the power for these comes from, would it be able to handle another fan???

it seems like a legit idea, seeing as how the rear of the heatsink has NO heat dissipation at all. which is the part that melted offcausing the old  card to die in the first place.

basically the thermal pads look like they gunked the card and it was unfixable, I have a post to it on the Alienware Forum, which i could link later,

 

is it a good idea, and will the VBIOS WORK with my 880M (DELL) from a clevo, (now in an alienware) im assuming they are compatible, as long as they are dell.

also would I be able to get a Y adapter for the inside of a laptop fan, that would be AMAZING, i know they sell them for Desktops.

Thanks

 

 

Edited by moaker
Link to comment
Share on other sites

  • 1 year later...

Interested to know how this goes! However I don't have any major thermal throttling running the 880m on the A12 unlock Bios. I also had to sacrifice my HD Audio entirely though. I still can't figure out if its a bad Bios install or im doing something wrong with the driver installs after I upgraded the GPU(Shrugs) Doesn't matter anyways because I use a work aroundxD. You can always try reapplying the thermal grease compound, As well as make sure the thermal pads are placed properly over the memory. I also red somewhere as well that if you upgraded from another GPU sometimes you have to cut back on some of the thermal padding itself. To allow the GPU to have a larger thermal dissipation radius. 

 

Link to comment
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.