Jump to content
Review: E-Win Champion Series Gaming Chair Read more... ×
EwinRacing Flash Series Gaming Chairs
JChristian

One of the 680M SLi might be dead after an update?

Recommended Posts

My issue: one of the two 680M GPUs started displaying an "Windows has stopped this device because it has reported problems. (Code 43)".
My hardware: Clevo P37EM / Sager NP9370
My OS: Windows 10 Enterprise 2016 LTSB x64
 
I keep the OS always up-to-date (Windows LTSB only ships security and fix updates). I also have very few softwares installed. Basically, my computer was working normally, but today I was playing Overwatch (which I always play) and after some hours, I suddenly heard a Windows beep, the game froze and the computer restarted. When I was back at the desktop, I noticed the resolution was not right and then I opened the Device Manager to see that one of the 680M was giving a Error Code 43. Both GPUs appear on my BIOS setup, the BIOS correctly identifies them as 680M.
 
I found it strange, so I check my GPU VBIOS and noticed something odd, one of them was at 80.04.33.00.10 and the other was at 80.04.67.00.01 (I get these drivers here). I know for a fact that since some older NVIDIA Driver, the VBIOS must be 80.04.33.00.10 or else I got some errors on this SAGER model, so I flash 33 on both a while back. I then proceeded to flash the correct version again. When I run DDU I notice it only detects the VBIOS version for one of the GPUs, the other one doesn't show the VBIOS version. My results are:
 
NV Driver 398.36
 
ROM 33
PCI BUS 2 working
PCI BUS 1 error code 43
 
ROM 67
PCI BUS 2 working
PCI BUS 1 error code 43
 
 
NV Driver 391.35
 
ROM 33
PCI BUS 2 working
PCI BUS 1 error code 43
 
ROM 67
PCI BUS 2 working
PCI BUS 1 error code 43
 
 
Can a Nvidia update or Windows update brick a GPU? How can I know if it's a software or hardware issue? I'm afraid that one GPU died as I don't have the money to replace it now and it would be difficult to find a spare new 680M (which is now old hardware) where I live. I'm panicking a little...
Edited by JChristian

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Brian
      Following the release of NVIDIAs new 436.02 driver which I mentioned in an earlier article here, I've decided to make a quick and dirty video showing off NVIDIAs new Sharpen filter which is part of their Game Filter feature. It works with the most popular APIs including DX 9, 11, 12 and Vulkan and can be set on a per-game basis with granular settings of 0-100 unlike AMDs RIS which is limited to Navi and lacks DX 11 support.
       
       

      View full article
    • By Brian
      Following the release of NVIDIAs new 436.02 driver which I mentioned in an earlier article here, I've decided to make a quick and dirty video showing off NVIDIAs new Sharpen filter which is part of their Game Filter feature. It works with the most popular APIs including DX 9, 11, 12 and Vulkan and can be set on a per-game basis with granular settings of 0-100 unlike AMDs RIS which is limited to Navi and lacks DX 11 support.
       
       
    • By Axel de S
      Hello guys,
      I have a GT72VR 6RE with G-sync MSI Laptop. Sadly the GPU is partially dead (artefacts all over the screen, crashes, windows detecting a damaged hardware etc...).

      So I bought an other GTX1070 MXM on ebay, which was used in a Vortex G65 6RE before.
      Sadly, when I plug the new GPU in the laptop, the laptop screen stays completly off, but i can use the HDMI port. So i though that I would just have to flash the vbios to the one I was using on the GPU that died, but I couldn't because of a mismatch betwen the PCI Device ID.
      The new GPU ID is : 10DE 1BA1 - 1462 11AF and the previous GPU ID was :10DE 1BE1 - 1462 11AF
      Pretty close right? but the A1 and E1 variation are fcking everything up. I've read that 1BA1 is for non G-sync and 1BE1 is for G-sync. I've also read that the G-sync variation is not part of the card but is an external part no on the GPU board.

      So now I'm wondering what can I do : is there a way to force the vbios flash or to change the PCI ID ? I really need some help here. I'm no expert and I've try as much as I could. Maybe I need to do some vbios editing but I don't really know how to do it and what to do exactly to make this work.

      Thank you very much for your help guys
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.