Search the Community
Showing results for tags 'overclock bios'.
Found 3 results
.If you're interested why not all modified BIOS versions can be flashed the 'usual' way with the official tools, read this:http://forum.techinferno.com/alienware/2252-information-about-bios-updates-a07-a08-higher-m14xr2-m17xr4-m18xr2.html M18x R2 - 'unlocked' BIOS versions The following BIOS of the Alienware M18x have been modified so that all hidden menus and options are visible. It will allow you to further tweak your system and optimize its peformance. Most of the options are only meant for advanced users. Don’t change anything you’re not sure about. It's possible that you see options which don’t work for your system, so be careful when changing settings. In case you mess up and your system refuses to boot applying new settings, remove the AC adapter, battery and coin cell battery in order to clear the non-volatile ram of the BIOS. This should fix most issues. *UPDATE*Instructions: There are two ways to flash the modified BIOS: Downgrade to stock A03 by using the USB recover procedure. (Thanks @Scott Matusow for summarizing the procedure). Make sure to closely follow the instructions, and wait until the system is done with the flash. Once you're on A03 flash the modified BIOS using the regular way (using the tools provided by Dell)..This method seems to work very well on the M18x R2, at least as long as you do as instructed. It can be a bit scary though since you can't see what's happening. .. Flash the BIOS from DOS with the FPT tool. This will only flash the BIOS part and leave out the EC and so on. It's a really safe option when done properly and less scary since you see the progress and information on the screen. For the USB recovery method follow the instructions in the link above. Second possibility - flashing from DOS: Prepare an USB drive so that it can boot DOS. If you don't know how to do this, check the instructions in the spoiler. . Grab the DOS version of fpt for flashing, and my 'prr tool' to circumvent write protection.. Download a '[FPT]' labeled version of the unlocked BIOS. Put the DOS version of the flash tool on the root of the prepared USB stick (fpt.exe and fparts.txt), along with the prr.exe and the file you want to flash (plus the included flash.bat). . Restart the system and boot from your USB stick. Run prr.exe, then flash the bios by executing the flash.bat file. Wait until the tool completes the flash. If the verification is okay, reboot, else flash again.. Go to the bios, load the default settings and reboot. Done. NOTE: If you want to use an unlocked BIOS newer than A03 I highly recommend to first flash the desired version of the unmodified BIOS (grab it at the Dell download site). Once you're on the version you want to unlock, follow the DOS flashing procedure described above. If you want to go A03 or earlier, the best thing to do is using the USB recovery method. Here two pics of the most interesting options: ********** Thanks @Riri-Fifi for the pics and testing! Thanks @johnksss for testing my prr tool! ********* Flash and use at your own risk. I don't take any responsibility for possible damage on your system. ___ The software which I provide here ('prr tool') comes with absolutely no warranty to the extent permitted by applicable law. Download the bios files referened in this post from here:
Turbosheild posted a topic in MSIHi! So, I am new here, and I was hoping that I could get some advice regarding flashing the vBios of my GTX 680M, residing within my GT70 (Valkyrie CZ-17, from iBuyPower). As time have progressed, what was once a cutting edge graphics chip is now struggling to retain the flair it once held, and I with to restore it to its former glory, ie) squeeze every ounce of performance that I can out of this card. This being said, while I have a basic-intermediate knowledge of overclocking, I am entirely new to the concept of flashing a vBios, and thus I am a bit apprehensive as the last thing that I want to do is fuck up a $600 graphics card. I currently run a moderate overclock of 800 MHz, and 2000 MHz on the memory, using the stock vBios. My goal is to achieve a base clock of 900+ MHz, perhaps even 1000ish with a sudo-boost of sorts, if that is possible. I have an MSI GeForce GTX680M (4GB) Running - GeForce 335.23 WHQL - as a driver. The current BIOS is - 80.04.33.00.24 And the GPU is (obviously) a GK104, revision A2. I have been looking through the forums, and found what I thought to be a good BIOS, but it said that I didn't have access to the download, and all that I can find now is a vBIOS for a Clevo 4GB 680, and I have an MSI 4GB 680, so I worry of the consequences of using a such a combination of soft and hardware. ____________________________________________________________________________ Additionally, I have a question in regards to managing the thermals in this laptop. I currently have two external solutions, one moderately priced cooling pad with a 92mm fan, and a Jerry-rigged solution with a 10" desk fan that can successfully keep the laptop below 68C (stock clocks), with an ambient temp of ~20C. So, my question regarding cooling, are there any internal modifications that can be done to increase the potency of the internal fan, if the internal fan can be upgraded for a more effective model, or if there are any software tricks to turn the fan up to 11, metaphorically speaking. Any and all help would be greatly appreciated. -Emma (Seriously, I would really appreciate some advice here)
Hi guys, I'm interested in increasing the voltage of my graphic card. I followed the tutorial to overclock my card with a custom vbios but i still cant modify the voltage in the nvidia inspector tool. How could i modify my vbios to increase the voltage ? Here is the tutorial im talking about : http://forum.techinferno.com/asus-gaming-notebook-forum/2538-%5Bg75vw%5D-modified-bios-vbios-higher-overclocking.html Thanks a lot