Jump to content
EwinRacing Flash Series Gaming Chairs
mw86

Help HP HDX 18t 1200-CTO w/ Nvidia GT130M and Intel Core 2 Quad Q9000

Recommended Posts

Help HP HDX 18t 1200-CTO w/ Nvidia GT130M and Intel Core 2 Quad Q9000

the issue is i have two identical comps like that i work on one my brothers and the other my mothers... my moms keeps temps in check and even undervolted q9000 to 1.05v from 1.25~ did the same on my brothers... the prob is these comps have one fan and one copper pipe going over the cpu and gpu causing havok when cpu or gpu heats up. Now my moms handles good it was previously mine and i kept it clean... 3 years oldish on stock paste. My brothers constant overheat probs i even repasted his on gpu and cpu.... so i need help as i have no experience on nvidia vbios flashing and editing downloaded nhibitor and nvflash and went to backup file in windows and it wont recognize eeprom as it says. help i can create a bootable usb drive have one from flashing ATi cards.... onece i have bios backup i can reflash with a little less volts hopefully running much cooler. Any links on directions on backing up bios and flashing outside of windows on nvidia hardware... i dont think its MXM is that a prob? my moms i'm even able to run a small overclock of 680-550-1700... core,mem,shader... stock is 600-500-1500 and dont get high temps even on Skyrim yes couldn't belive with graphics lowered enough this plays decent on here.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Similar Content

    • By ReverseEffect
      3dMark11 Performance Preset Benchmark: http://www.3dmark.com/3dm11/11262792
       
      Required items:
      1.) Lenovo u310 (I have a Core i3 - Ivy Bridge, 8GB RAM)
      2.) 65CN99WW unwhitelisted.
      3.) eGPU (I used a EVGA GTX 750 Ti from another computer I had).
      4.) EXP GDC mPCIe Edition adapter (got from eBay - banggood seller).
      5.) ATX power supply (I used a 600W PSU from another computer I had).
      6.) USB wireless.
      7.) External monitor, keyboard, and mouse.
       
      Steps:
      1.) Obtain and install a unwhitelisted BIOS. If you are unable to obtain a unwhitelist BIOS, I think it might be possible to bypass it with Tech Inferno Fan's Setup 1.x (may need confirmation as I haven't used it myself yet.)
      2.) Shutdown computer and remove all USB devices, ethernet cables, power cables, card reader cards.
      3.) Remove mPCIe wireless card and detach antennas.
       
       
      4.) Attach EXP GDC external mPCIe cable to the former wireless slot and screw down.
       
       
      5.) Attach HDMI end of the mPCIe cable adapter to the EXP GDC device.
       
       
      6.) Attach graphics card to the EXP GDC device (I moved my laptop off the desk and onto the side shelf to make room on the desk for the monitor/keyboard/mouse).
       
       
      7.) Using the power cable adapters that came with the EXP GDC device, I hooked in my ATX power supply's 20 pin and CPU 4 pin cables. Then hooked the other end (8 pin) into the EXP GDC device. My EVGA 750 Ti also required that I use an additional PCIe power cable (6 pin) in the top of the card.
       
       
       
       
       
      8.) Then I attached my misc devices (HDMI monitor, USB keyboard/mouse/wireless adapter), and hooked in my PSU and powered it on (below is image of final product, also moved HDMI cable out of the way).
       

       
      9.) Power on your computer and let it install the standard VGA drivers and then install your drivers (I didn't have to go in the BIOS for any graphics settings, which it doesn't have anyways, nor did I have to disable iGPU in Device Manager before the card was added).
       
      Extra Info:
      I found that most games will play on med settings with about 45 FPS with this particular card.
      BDO: Upscale on - Anti Aliasing on - SSAO off - med settings.
      Skyrim: Med-High settings.
      Fallout 4: Med settings.
       
      (EDIT 5/19/2016) > Images added.
       
    • By narbardarse
      ok, so, i have a serious problem atm.
      im trying to mod my bios so that i can go past the normal overclocking limit. however, everytime i try to do it, it always says "file size does not match existing bios size!", and it's really annoying, since i had to find everything myself, as no one else online tried this on my specific model, besides me. (which surprises me, really)
      this is the guide im following:
      So this is my detailed description how I managed to mod and overclock my GTX 960M in my Lenovo Y50-70. Please note: it is very dangerous to play with the BIOS, so you need to be very careful! I take NO RESPONSIBILITY for any damage or misuse of the information below! Use it AT YOUR OWN RISK!
       
      -------
       

      Necessary tools:
      A. Fptw64 from Intel (9.5 or above)
      http://forum.hwbot.org/showthread.php?t=75024
      B. PhoenixTool (2.50 or above)
      C. Maxwell II BIOS Tweaker (1.36)
      https://www.techpowerup.com/downloads/2562/maxwell-ii-bios-tweaker-v1-36/
       
      -------------------------
       
      How to flash Modded BIOS:
      0. Flash the latest (3.03 now) official BIOS
      1. From Windows, start 'cmd' as Administrator and read your your BIOS via Fptw64:
         Fptw64 -d BIOS.ROM -bios
      2. Reboot, enter your BIOS and check "Enable downgrading BIOS" feature (we need to downgrade first in order to flash the modded BIOS)
      3. From Windows, downgrade to 1.13 (this is necessary because the newer BIOSes have protection against mod-ding)
      4. After reboot & reflash, start Windows, then enter standby, wait a bit, then wake up the machine
      5. Create your modded BIOS, see separate list below
      6. Start 'cmd' as Administrator and write your _modded_ BIOS via Fptw64:
         Fptw64 -f BIOS_MODDED.ROM -bios
       
      -------------------------
       
      How to create modded BIOS (point 5 above):
      5.1 Start PhoenixTool.exe from Phoenix Tool 2.50 and open your previously saved original BIOS.ROM from point #1 above
       .2 The tool analyses it and shows some messages, click OK
       .3 Now you can find your vBIOS in the "DUMP" subfolder in the folder containing your BIOS.ROM, with the file name:
          BE13645B-2C2C-44D2-A64F-0EA052C34597_1796.ROM
       .4 Create your modded vBIOS, see separate list below -> let's call it 960M_OC.MOD
       .5 Click on "Structure"
       .6 Open "EFI BIOS" tag
       .7 Open second "File Volume {7A9354D9-...}" tag
       .8 DXE Core -> Compressed Section -> Raw section -> File Volume {7A9354D9-...}
       .9 In the very long list, find the following tag (usually displayed at around 80% of the list):
          Freeform {BE13645B-2C2C-44D2-A64F-0EA052C34597}
          This is the item containing the latest vBIOS
       .10 Open the tag, then "GUID defined section", then click on Raw section. "Internal number" (in the top right corner) should be 1796 for BIOS 3.03.
       .11 Click on "Replace" and select your modded vBIOS (called 960M_OC.MOD above)
       .12 Click exit "Exit" and say Yes to "Save changes?"
       .13 Close the Phoenix Tool; now you should have your BIOS.ROM updated (the original will be saved as BIOS.ROM.OLD for safety)
       
      -------------------------
       
      How to create modded vBIOS (point 5.4 above):
      Use Maxwell II BIOS Tweaker to change BE13645B-2C2C-44D2-A64F-0EA052C34597_1796.ROM;
      5.4.1 Open the ROM
         .2 Change "Boost Clock" on "Common" tab to the new boost-ed maximum value
         .3 On "Boost table" tab, use the slider in the right bottom corner to increase your max boost-ed value to the same number
         .4 On "Boost states" tab, at P00 profile, change the MAX values in the GPC, L2C and XBAR fields to the same max boost-ed value
         .5 Save your modified BIOS and rename it to 960M_OC.MOD
       
      (My boost-ed max value was 1359 MHz. I could then use MSI Afterburner's software tuning -> my 960M could reach 1454 MHz without voltage increase.)
      i know that it's for a different laptop, but its basically the same
      ill provide more info when im home
    • By Brentjuh2000
      Who can help me with modding and getting my 980M working?
      I replaced the M6100 that was originally in the laptop with a 980M but I can't seem to get it to work. I keep getting Code 43
      the Hardware ID : PCI\VEN_10DE&DEV_13D7&SUBSYS_15CD1028
      I heard i need to modify and INF file but i have no experience with it
       
      The vBIOS is from MSI
       
       
    • By Klem
      If someone wants upgrade Wi-Fi card and remove witelist, or unlock hidden additional menus and settings, or unlocked vbios for overclock NVIDIA card, then you can post your request in this thread.

      It's for Lenovo Z710, Z510 only!
    • By Andrew2009
      Please could you check if it is possible to unlock my A17 BIOS? I have Alienware 17 R5(2013). 120 Ghz 3D. gtx 980 m. I want upgrade to 1070 but I have dark picture. Turns on but does not start with 1070. 980m-All good. What could it be?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.