Search the Community

Hello all, I recently put together my egpu configuration using the video below down to a T. Every part of my set up is in this video and I've done exactly like this guy has said to make my set up. I've gotten my egpu to work finally by plugging in the thunderbolt2 cord when both the MacBook and egpu are powered down. Then I power on my back into the selection screen to choose windows or mac. Then I turn on my egpu and hope for the best. I've found this works about 30-40% of the time so if someone has a way to increase my chances feel free to comment. I'm using a MacbookPro 13in Retina with dual core processor and Intel Iris 6100 (Late 2015 MacBookPro 13in retina). Anyways once I am booted into windows (I'm using windows to use the egpu on the internal screen because this was meant as more of a mobile device) and I've checked the device manager to make sure the gtx960 is working properly (sometimes I get "no drivers are installed for this device and I have to reboot and try again) I try and run a game. I use WoW as a test for my graphics card. I have msi afterburner installed and I play WoW off an external HDD since I have the 128gb version of the MacBook pro. The graphics card fan never starts to spin. I monitor afterburner and at 50degrees celsius it still hasn't kicked on. I've only upped the graphics on WoW to about half 5/10 and after a few minutes of being on that setting the game crashes and I get a blue screen telling me there was a problem with windows. I'm at a loss and really upset since I've payed 400-500$ for this and it's not working and has given me a lot of trouble. There has to be someone out there who has this set up and dealt with this issue. I can't be the only one. I think the graphics card tends to crash around 60 degrees celsius and even using msi afterburner I've tried to increase the fan speed but even at 100% the fan just tilts a little bit when I look at it and never takes off. When the system first turns on though the fan seems to spin at 100% but after about 20 seconds the fan stops even though the graphics card is detected. So if anyone has dealt with this issue or knows how to overcome it please let me know. I shouldn't have to buy anything else to make this work since the guy in this video seems to have his set up working just fine. Thanks in advance everybody. Ps. Please help!

Hi there! As Afterburner 4.3 beta 14 gives access to the voltage curves, I plaed around some and found out that one can undervolt the GPU with some success. After locking my GPU clock on 1709 mhz @ 800mV and the RAM clock on 4498 mhz I was able to run the Witcher 3 with the same framerate (73.5 FPS 1080p ultra without Hairworks) as under standard voltage - anyhow my notebook was consuming about 15-17 watt less (152 instead of 168). With G-Sync enabled (one might as well say with FPS locked to 60) the result is even mor drastic, as the GPU won`t clock up as the load decreases in light weigth scenes. I could reduce the power consumption about 20-30 watt (128 instead of 156), depending on the GPU load. Perhaps some of you guys care to post their results, and perhaps are able to answer one question: I thought with GPU clock locked to 1709 an RAM to 4498 I thought I`d surpass the standard settings in regard to the FPS - still this is not the case. I know this has to do with th undervolting, but still... Best regards phila

I am using msi afterburner to overclock the 675mx on my ibuypower cz-17 (i am pretty sure it uses the same hardware as msi) When i do so GPU-z Gives me weird results. The results that i am getting seem like the core clock is stuck at 653mghz when it should be 800mghz. The is room in the gpu-z graph to go up when overclocking is enabled. i tried all the power save options to max performance. I also tried to lock voltage. No good. I cant flash a vbios because i cant find one (other then the one on this site that i cannot download ) if anyone has a suggestion or a link to a download for the 4gb 675mx bios let me know.