Jump to content
EwinRacing Flash Series Gaming Chairs
x6tus

Noisy Gtx980? 2015 15" MBP, Thunder2

Recommended Posts

 

Hi, I've not posted on here since I built my eGPU for my 2015 MacBook Pro over a year ago. That unit was an Akitio Thunder2, RM 650W PSU, CoolerMaster 130 case, powered riser cable with a Zotac GTX 770 card.

 

It's mainly used for playing Elite Dangerous on and it has been working perfectly.

 

Recently I had the opportunity to upgrade the GTX 770 to a GTX 980 Reference card. It was pretty much a straight swap out except for the cards power connectors. On the GTX 770 these were 1 x 8-pin and 1 x 6-pin connectors. On the GTX 980 these are 2 x 6-pin connectors.

 

Simple enough with my 650W PSU I just switched connectors. I am using the same powered riser cable for the PCIe connection.

The unit boots up and works okay on Windows 10 via the display port connection. It will even play Elite Dangerous on Ultra settings and give a steady 60fps.

 

So all good! Why am I posting here and asking for help???

 

Well, I noticed that when playing Elite Dangerous I could hear a high pitched electronic screaming noise coming from the unit. At first I thought it was the GTX 980 power coil as apparently they do sometimes do this. However on closer inspection the noise is coming from the Akitio board.

 

It appears to be power related, so I tried to stress the card (and hopefully use more power) by using 3D Mark 11. Sure enough when running the benchmark tests the Akitio board makes a very high pitched electronic screaming noise. The noise stops when the tests stops. So it is caused by load on the graphics card and therefore I presume power, or lack of it.

 

Do you think power is the problem here? If so, what should I do? I don't use the 2.5mm power adapter input on the Akitio board because my powered riser cable has a MOLEX adapter attached to it. 

 

Should I scrap the powered riser cable and get a non-powered version and then create a MOLEX to 2.5mm DC adapter plug for the Akitio power socket? Would that supply enough power for the GTX 980.

 

The GTX 770 never had this problem, but I presume the GTX 980 draws a lot more power under load.

 

I've attached some pictures below. Any help or advice you can give would be appreciated.

 

Thanks,
X6

aa.jpgbb.jpgdd.jpg

ee.jpg

Share this post


Link to post
Share on other sites

Noises because of GPU load are more common nowdays with the Maxell GPUs! That is because the GPUs now have a very complex power management, allowing the GPU to switch extremly fast between power states and loads.

A very common problem are the GTX970 cards with poor coils and weak power system on the card.

A bad PSU can cause the same problems, but I would say that the AKiTiOs power system was not made for such high loads and reacts with that sounds. It's no problem, just a bit uncomfortable.

Share this post


Link to post
Share on other sites

Okay, that's good to know. The card does operate correctly even with the noise.    

 

Are you saying there is no advantage to switching to a MOLEX to Barrell connector instead of a powered PCIe riser cable?  

Share this post


Link to post
Share on other sites

It appears to be :)   I guess I'll be using headphones anyway so I won't hear it.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By ReverseEffect
      3dMark11 Performance Preset Benchmark: http://www.3dmark.com/3dm11/11262792
       
      Required items:
      1.) Lenovo u310 (I have a Core i3 - Ivy Bridge, 8GB RAM)
      2.) 65CN99WW unwhitelisted.
      3.) eGPU (I used a EVGA GTX 750 Ti from another computer I had).
      4.) EXP GDC mPCIe Edition adapter (got from eBay - banggood seller).
      5.) ATX power supply (I used a 600W PSU from another computer I had).
      6.) USB wireless.
      7.) External monitor, keyboard, and mouse.
       
      Steps:
      1.) Obtain and install a unwhitelisted BIOS. If you are unable to obtain a unwhitelist BIOS, I think it might be possible to bypass it with Tech Inferno Fan's Setup 1.x (may need confirmation as I haven't used it myself yet.)
      2.) Shutdown computer and remove all USB devices, ethernet cables, power cables, card reader cards.
      3.) Remove mPCIe wireless card and detach antennas.
       
       
      4.) Attach EXP GDC external mPCIe cable to the former wireless slot and screw down.
       
       
      5.) Attach HDMI end of the mPCIe cable adapter to the EXP GDC device.
       
       
      6.) Attach graphics card to the EXP GDC device (I moved my laptop off the desk and onto the side shelf to make room on the desk for the monitor/keyboard/mouse).
       
       
      7.) Using the power cable adapters that came with the EXP GDC device, I hooked in my ATX power supply's 20 pin and CPU 4 pin cables. Then hooked the other end (8 pin) into the EXP GDC device. My EVGA 750 Ti also required that I use an additional PCIe power cable (6 pin) in the top of the card.
       
       
       
       
       
      8.) Then I attached my misc devices (HDMI monitor, USB keyboard/mouse/wireless adapter), and hooked in my PSU and powered it on (below is image of final product, also moved HDMI cable out of the way).
       

       
      9.) Power on your computer and let it install the standard VGA drivers and then install your drivers (I didn't have to go in the BIOS for any graphics settings, which it doesn't have anyways, nor did I have to disable iGPU in Device Manager before the card was added).
       
      Extra Info:
      I found that most games will play on med settings with about 45 FPS with this particular card.
      BDO: Upscale on - Anti Aliasing on - SSAO off - med settings.
      Skyrim: Med-High settings.
      Fallout 4: Med settings.
       
      (EDIT 5/19/2016) > Images added.
       
    • By Sarafan
      Does anyone have experience with this?

      Some threads I've seen have done it on a 17 inch laptop, I was wondering if it was possible on the 15 inch version as well.

      What issues will I face? I read about having to have a custom BIOS and vBIOS..but also HDMI/audio issues.

      I guess I should also upgrade my CPU, which runs really hot (i7 4800MQ), but not sure another Haswell chip will run any cooler.

      I've used liquid metal and even that hasn't changed temperatures much, it still reaches 93C pretty easily.
    • By sigma
      I have a Clevo P170EM with a GTX680m from 2012 and it's starting to show weight of the years  
      I would like to squeeze little more performance out this "outdated" GPU.
      Can someone help me ?
       
    • By mrsmile1015
      Just recently puchased a Clevo Gtx 780m on ebay and inserted it into my Alienware m17x r4. I'm terrible dissapointed to find the BIOS a12 unlocked and device mananger doesn't detect it at all. Are there some steps I have to undergo to make it work? 
    • By mrsmile1015
      Just recently puchased a Clevo Gtx 780m on ebay and inserted it into my Alienware m17x r4. I'm terrible dissapointed to find the BIOS a12 unlocked and device mananger doesn't detect it at all. Are there some steps I have to undergo to make it work? 
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.