Jump to content
EwinRacing Flash Series Gaming Chairs
copyninja

!!help!!! I want to flash my nvidia gforce gtx 680m 4gb mxm 3.0 (alienware m18x r1)

Recommended Posts

ITS INTALLED IN MY ALIENWARE M18X R1

THE ALIENWARE HAVE THE BIOS 04 MODED FROM THIS PAGE

THE GTX 680M 4GB WAS PULLED FROM A ''CLEVO P170EM'' AND THE ACTUAL Vbios IS ( 80.4.29.0.1 )

AND I SAW A POST WHITH A OVERCLOCKED VBIOS IN THIS PAGE.

Clevo 680m (80.04.33.00.10) 'OCedition' revised v01 EDIT by svl7 ...THIS ONE...

CAN IT WORK IN MY ALIENWARE OR IT WILL BRICK MY LAPTOP?

HELP!:confusion::confusion::confusion:

post-37385-14495000685484_thumb.png

post-37385-14495000685645_thumb.jpg

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Similar Content

    • By Rjleo
      Hello, I need modified bios For AsUs G75vw with Gtx670MX i try someone moded bios but it didn't works for me ..laptop just died ... im w8ing for the Ch341a programer i orderd .. when it cames i'll revive at default ..so need somebody to made that bios for me. 
    • By Rjleo
      Can somebody tell me what is the vbios? or whare is it ? on GPU or Motherboard ? and Can we Use older GPU vBios FoR newer GPUs? 
    • By Henrik9979
      Okay here is what's going. I have a alienware m18x r1 running an amd 8970m, I wanted to upgrade it to crossfire but I could see a 8970m was more expensive than a r9 m290x
      So I decided to buy a r9 m290x and see if I could make it work in my alienware and also run crossfire.
      Even though many shops refused to sell me one because the didn't think it would work in an alienware m18x r1 only in the r2.
       
      Here is the whole process.
       
      19/08/17 23:15
      No post bios showing when booting, so impossible to enter bios menu, but can boot into windows 10 with no problems.
       
      19/08/17 23:20
      Because I haven't deleted the old AMD 8970m the r9 m290x shows as a 8970m with no problems.
       
      19/08/17 23:34
      First performance test was a success. The r9 m290x changed p-state normally. The gpu fan start spinning normally. But because of no thermal paste, the test lasted 20 seconds because the temperature raised fast.
       
      20/08/17 00:00
      Created a backup of the vbios version
      015.032.000.004.044450
       
      20/08/17 00:10
      Flashed a new clevo vbios version 015.032.000.003.044465
      Caused the card to be corrupted and resulted the 8 beep code.
       
      20/08/17 00:35
      Finally managed to flash the back and return the graphics card to its original state.

      20/08/17 00:50
      Flashed a new dell vbios version 015.046.000.014.045579
      No change in behavior
       
      20/08/17 01:07
      After trying multiple vbios with no luck I finally found one.
      Dell vbios Version 015.041.000.000.044966
      Brings back the post bios screen and I can now enter the bios menu through the r9 m290x.
      Note: This vbios reduce the cards performance from 900 mhz to 850 mhz
       
      20/08/17 01:21
      After more testing I found one that is working with no limits.
      Clevo vbios version
      015.036.000.005.044618
      Brings back the post bios screen and I can now enter the bios menu through the r9 m290x.
      This will be the vbios I will keep at the moment.

      20/08/17 01:56
      I completely uninstalled the previous driver and installed the newest driver. The graphics card is recognized as a 8970m but works normal.

      21/08/17 20:15
      I have inserted my old 8970m in the secondary slot and will start testing crossfire.
       
      21/08/17 21:45
      I have found out that the fan for the secondary fan did not spin. The is a cable that have felt out. I will fix it now.

      21/08/17 22:00
      In my try to test crossfire compatibility, I installed the newest AMD driver 17.7.2 but as soon it installed the driver for the secondary card it caused black screen. Only booting the computer in safe mode brings the screen back.

      21/08/17 23:02
      After many frustrating hours I finally managed to get crossfire working with the r9 m290x as the primary card and my old 8970m as the secondary.
      I have flashed the same vbios on both cards so the r9 m290x shows up I device manager as a 8970m.
       
      I first installed AMD driver version 16.2.1
       
      Then installed AMD driver version 16.6.1 in order to play battlefield

      21/08/17 23:20
      First test run in battlefield 1

      21/08/17 23:40
      Battlefield 1 is flickering bad, this can maybe be solved with a new patch or driver.
      Other games I have tried is working perfect with crossfire on.


      Now what I would like to try is somehow force the r9 m290x driver to be installed and see if it will make it possible to run the latest AMD driver without getting a blackscreen.
       
      I have tried to edit the .inf file like you would do with nvidia but no luck.
      I have also tried to figure out how to edit the device id in the vbios, but I find it too complex.
    • By Klem
      Klem's_vbios_MSI_GTX770M_80.06.54.00.11_UNLOCKED
      1. Unlocked Nvidia core limit +135 MHz.
      2. Unlocked Power Limit.
      3. Unlocked Power adjustment by software (for example with Nvidia Inspector).
      4. Increased Power Limit and Power Target.
      5. Enabled some additional tweaks.
       
      If you liked my mod, you can buy me some beer:   https://www.buymeacoffee.com/ekushukovZ
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.