Hey guys, first post, but I thought I’d discuss my heatsink fan retrofit in my old M14x r1.
Old fan was loud and not very efficient: the air transfer rate was around 2 cfm (I’m assuming cubic feet per minute). Finally had enough and decided to swap out the crappy r1 fan/coughing pinwheel for a r2 fan (rated at 10.4cfm).
I found an old r2 heat sink on eBay (beware though that the heat sink for the r2 will NOT fit the gpu/cpu configuration for the r1. HOWEVER, the fan of the r2 heat sink it is attached to is a carbon copy fit into the r1 MoBo. A few philips head screws and a seal of good electric tape and BAM, you’ve got a significantly cooler and MUCH quieter intake fan in your old R1.
My CPU temps from before were around 87-88 max load in FSX, 65 for the GPU; bear in mind this is after a repaste. Now with the new fan, I’m not going over 77 degrees on the CPU, and the gpu stays around 58, all while being MUCH quiter. I’ll post pics of the walkthrough if anyone is interested.
Just thought I’d share with all you fellow loonies trying to squeeze every last frame and degree out of our “portable toaster ovens with a screen and keyboard”.
As the title say i have an old m15x with a 920xm, 8gb ram and just got a 770m to boost gaming perfomace but the drive wont install.
When I run GPU-Z I see the attached image which are all the correct stats of the card but not really the card and HWINFO64 is showing that its the correct card but again not anything else.
I've read about .inf issues and about vbios flashing but dont know how to do either or which would be best to try.
Any ideas which (if either) could be my problem and how to do either task or how to go about more trouble shooting. Any more info required just ask. Any and all help much appreciated.
I just want to play total warhammer:-(
Hi everyone, I was thinking of upgrading my ram from 8GB to 16GB 1600MHZ either Kingston/Crucial as my current ram usage is at always at 4GB now. Will upgrading make a lot of difference in the performance of the PC and will it improve the game play for GTA V as I am currently having massive lag with this game?
Thank you in advance.
I am new here, so I am sorry if I have posted this in the wrong section. Also, I realise this question has been asked before, but all of the other threads are really old.
So, my issue. I flashed the unlocked A08 bios with sata fix and everything worked brilliantly. Then, in my infinite wisdom I turned on UEFI mode in BIOS to see what would happen. What happened is it rebooted with 8 beeps (no screen) everytime I turned on. I looked at the other forums and did the whole usb recovery thing, however, I believed it was taking to long so I turned the computer off after the computer rebooted and beeped 7 times (cpu error). I tried taking out the CMOS to no avail. Now when I try the recovery USB the usb never seems to be loaded (light never comes on). Any ideas?
Thanks for all the help, and sorry for any mistakes I have no doubt made.
I have gone through a lot of pages of this forum (related to eGPU and overclocking) and they really are very useful but not able to find anything good for my laptop.
My laptop is Alienware M14Xr1 with following configurations :
Intel core i7 2860QM
Nvidia GT555m (3GB)
8GB primary memory 1600Mhz
750GB secondary memory 7200RPM (698.4 GB usable)
I want to use a eGPU setup in my system.
Could anyone please tell me whether it is possible or not to use -
In my system there are following ports available - 2xUSB3.0, 1xUSB2.0, 1xHDMI1.4, 1xMiniDisplayPort, 1xVGA, 1xEthernet1000mbps, (I think none of these will be helpful in eGPU setup )
But i have heard that if you remove your wireless card then you can plug in your eGPU there. Is it true,
Please anyone share your experience with me related to this setup.