Jump to content

Prokid

Registered User
  • Posts

    10
  • Joined

  • Last visited

Posts posted by Prokid

  1. On ‎3‎/‎19‎/‎2016 at 8:09 AM, odin2free said:

     Bought mine, no problems yet, 

    One gripe that i have though is the mPCIe side, they really made sure to seal the connector down...wide cable and flat which is very nice, but pain in the neck to move around and place on my notebook... W230ST.

    Over all solid uniit.

     

     

     

      

    The order of the switches should be both set to one.

     Youll need the software, setup 1.x

    Be patient though because nando got into an accident and right now its going to take some time to send software to people.

     

    also do you have it running to an external monitor?

     

    Any modded bios...

    idk if the L630 is blacklisting anything or has any updates for the bios.

     

     

     

     

     

     

    Hi :D

     

    Thank you so much for replying. Anyway, I managed to install the driver and be detected. But now my problem is code 12 error. I cant run it to an external monitor. Every time it runs to a monitor, after a few seconds it will shutdown the whole system.

  2. This is implementation Guide subforum --> ( Successful implementations on PC notebooks )

    You should post a thread in provisional guide subforum --> ( These guides are a work in progress )

     

    But it's okay. Nando will move this thread, immediately.

     

    I got that error too but when I override dsdt, it fixed the error.

    Try to follow this: 

     

  3. Good Day,

     

    My egpu driver is already installed and device manager requires to restart, but after restarting the egpu driver is undetected again. I'm using hotswap or hotplug trick while in sleep mode. Once the driver is detected and reinstalled again, it requires to restart the os.

    I'm trapped... Can someone please help and give me suggestions? thank you

     

    My setup:

    Toshiba l630

    core i5 2nd gen 2.53ghz

    4gb ram

     

    Pe4c 3.0 mpcie

    gtx 960

    generic psu 600w

     

    driver installed

    dsdt override done

    win7 64bit ultimate

  4. On ‎1‎/‎24‎/‎2016 at 7:59 AM, savage24x said:

    About to purchase a PE4C 3.0, can I use a standard PSU to power the card and the board, without needing the Dell power supply? Most likely going to be a 770 with a Latitude E6420.

     

    I'm using 600w generic psu. It's working fine with my GTX 960.

  5. On ‎3‎/‎11‎/‎2016 at 3:37 AM, gharimanto said:

    This is implementation Guide subforum --> ( Successful implementations on PC notebooks )

    You should post a thread in provisional guide subforum --> ( These guides are a work in progress )

     

    But it's okay. Nando will move this thread, immediately.

     

    Did you try set delay :

    - SW 1 = position 2

    - SW 2 = position 1

    That's work on me

     

    Good luck.

     

     

    I'm so sorry. my mistake :D

     

    anyway, still not working with delay switches. Is there a way that I can force the driver to install? I tried my other laptop and it works to dell inspiron. :(

  6. Good day guys,

     

    I'm still learning about egpu. Is my laptop compatible with pe4c 3.0 with gtx 960?

     

    Laptop:

    Toshiba Pro L630

    Core i5-430m 2.53ghz

    4gb ram

    no pcie slot

     

    vcard use: Zotac GTX 960

    PSU use: Generic 600w

    egpu: PE4C 3.0 mPCIE

     

    Issue:

    the egpu fan is spinning and I the led lights are turned on to 2 green lights. I replaced my wifi to egpu. The problem is my laptop not detecting the egpu. Sometimes it turns of my laptop after a few seconds. I tried all the combination of delay switch and the hotplug trick. Please HELP ME... thanks :D

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.