Jump to content
Apologies for the spam Read more... ×
EwinRacing Flash Series Gaming Chairs
Dr. AMK

Do I need to change the thermal pads for GTX 780m every time I want to repast?

Recommended Posts

Do I need to change the thermal pads for GTX 780m every time I want to repast? if so, what is the rghit thikniss for it? and where can I but it?

Clevo P570wm - GTX 780m SLI

 

Best Regards,

Thermal pads for GTX 780m.png

Share this post


Link to post
Share on other sites

Frozencpu is where i get mine.

and no you do not have to but depends on how often you change your paste...

 

go with .05 or 1.0mm thats what i go with...dont need to go with anything to crazy special.

  • Thumbs Up 1

Share this post


Link to post
Share on other sites
On 4/2/2016 at 1:06 AM, odin2free said:

Frozencpu is where i get mine.

and no you do not have to but depends on how often you change your paste...

 

go with .05 or 1.0mm thats what i go with...dont need to go with anything to crazy special.

Thanks @odin2free for your kind advice..

Share this post


Link to post
Share on other sites

Is there a significantly difference? I dont use thermal pads and have 65 temperature with my 780m OC +135.


 

Share this post


Link to post
Share on other sites

Wait

Are you using pads on the die or on the chips?

 

Dies = paste

Chips = pads

 

The reason people change pads is because of age.

Older= Pads change

Newer = Dont need to UNLESS you notice something is wrong with the pads such as CRACKS fractures tears etc....

 

 

 

 

@Dr. AMK Did you actuallly put paste in that little regulator are (think those are regulators to lazy to look up layouts)....id just go pads on those and make sure they touch some copper or aluminium to passively cool or actively cool dependant on what the entire heatsink cooling set up looks like)

 

  • Thumbs Up 1

Share this post


Link to post
Share on other sites
6 hours ago, odin2free said:

Wait

Are you using pads on the die or on the chips?

 

Dies = paste

Chips = pads

 

The reason people change pads is because of age.

Older= Pads change

Newer = Dont need to UNLESS you notice something is wrong with the pads such as CRACKS fractures tears etc....

 

 

 

 

@Dr. AMK Did you actuallly put paste in that little regulator are (think those are regulators to lazy to look up layouts)....id just go pads on those and make sure they touch some copper or aluminium to passively cool or actively cool dependant on what the entire heatsink cooling set up looks like)

 

Dear @odin2free thanks for your advice, for sure I'm using past for the dies, but I didn't change sny pads, it looks OK but compressed, the Temp's for all is good and I didn't face any problems. I'm just want to make sure that everything is perfect.

Share this post


Link to post
Share on other sites

Do you have to use pads? how do you determine pad thickness does it all have to be level accross the face?

Share this post


Link to post
Share on other sites
On 24/4/2016 at 11:49 PM, odin2free said:

Wait

Are you using pads on the die or on the chips?

 

Dies = paste

Chips = pads

 

 

 

How different? I just pasted all of them on the vga, does that cause any problems?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Kunal Shrivastava
      Hi guys, I am the proud owner of a Clevo p775dm3-g notebook purchased from azom.systems (authorized Clevo reseller in India, Model rebranded as Azom Legion-17.3 inches). Here are my specs:

      Core i7 7700 (non-K version): undervolted by 110 mv and turbo boost disabled in BIOS- machine uses prema mod BIOS.
      GTX 1080: undervolted by 100 mv on all frequency steps using MSI afterburner voltage/frequency curve editor. clocks are untouched.
      16 GB DDR4: Cant remember clocks.
      1440p 120 Hz screen: No tinkering done to refresh rate.

      CPU has been delidded and repaste has been done on both CPU/GPU dies with gallium based TIM-Coolaboratory liquid ultra if I recall correctly.

      My issue is GPU hitting max temp limit of 90 degrees while playing DOOM and framerate drops from 110 avg to mid 60s-70s with horrible stuttering- this is thermal throttling for sure.

      System was running beautifully after repaste at 86 degrees max/ 77 degrees average at 100 percent fan speed. A month later I decided to see how much further I could push the system and ended up undervolting the CPU/GPU and RAM even further. The RAM undervolting part didnt work as well as I'd hoped, and I ended up resetting the BIOS to undo everything and reapply the previous setting (-110 for CPU with turbo boost disabled.) 

      I noticed that immediately after BIOS reset, both my CPU and GPU temps were 5-10 degrees higher even with the undervolt/underclock applied. Also, I think the fans were a bit louder before I reset the BIOS which leads me to believe that for some reason the fans are now capped at 80% max fan speed. There doesnt seem to be a fan speed selector in the BIOS or anywhere else so I cant say for sure whether this is a fan related issue or something else.Before the reset I could override the BIOS setting and set the fans to 100% by pressing fn+1, could I have done something to that setting after resetting the BIOS ? I dont think I have damaged the CPU or GPU as temps are holding fairly steady at 90-91 degrees and laptop doesn't shut down while gaming.

      If I have overlooked something or if anyone reading this has any solution help would be greatly appreciated.
      All settings/drivers/windows version/app version are exactly the same before and after BIOS reset.
    • By BAKED
      BAKED BIOS FOR TM, KM, DM, P6, P4 SERIES with most menus and options unlocked.
       
      THESE BIOS MODS ARE ONLY FOR PEOPLE WHO KNOW WHAT THEY ARE DOING!
       
       
       
      NEW:
      I'VE BEEN BUSY WITH SOME STUFF PLUS MY SYSTEM HASN'T BEEN WORKING FOR SOME TIME BUT I SHOULD BE ABLE TO CONTINUE MY WORK SOON 
       
      I'M CURRENTLY WORKING ON V3.0 WHICH WILL INCLUDE UPDATED UEFI DRIVERS, MICROCODE BIOS SCREEN SHOT SUPPORT AMISCE SUPPORT(For some models) PLUS MORE. 
      I'M ALSO WORKING ON MODS FOR OTHER MODELS TOO.
      ALL TM, KM AND DM SERIES ARE V2.0 AND NOW HAVE WINDOWS FLASHER INSTEAD, JUST EXTRACT AND RUN FLASH.BAT
       
      WARNING! BIOS FLASHING IS RISKY SO MAKE SURE YOU KNOW WHAT YOU'RE DOING BEFORE PROCEEDING. 
      FLASHING THE WRONG BIOS OR INTERRUPTING THE FLASHING PROCESS WILL BRICK YOUR SYSTEM! 
      USE AT YOUR OWN RISK!
       
      TM, KM AND DM SERIES
       
      P6 AND P4 SERIES
       
      INSTRUCTIONS
        IF YOU LIKE MY WORK FEEL FRE TO BUY ME A COFFEE   ENJOY!
    • By racerxdl
      Hi all,
       
      It has been a while since I did anything to my laptop (Clevo P670RG-G) and since I recently got a VR Headset I wish I could overclock my GPU a little. So far the NVidia software (on windows) doesn't allow me to overclock it (the linux sort of allows, which some custom Xorg options) so I decided to give a try modding the vbios.
       
      I read all sorts of issues / guides about it, and it seens that the hardware topology (where the vbios is stored and how things are connected) changes from machine to machine.
       
      What I know about my laptop is that it has two VBios, one for Hybrid Mode and one for Discrete Mode. I'm currently running the discrete mode.
       
      I dumped my VBios using GPU-z and opened up in Maxwell II Bios Tweaker. Everything seens fine so far.
       
      So I have few questions about it:
       
      - There is a way to just unlock the VBios to show the overclocking options in NVidia software? (That way I dont need to reflash to change clocks)
      - I can just flash this GPU-z dump to my VBios?
      - If I brick my GPU, that GPU-z dumped image is the raw SPI image, so if I managed to physically access the VBios, I can just reflash over it?
      - I saw some people saying that I might need as well to flash the main laptop bios as well, is that really needed?
       
      Thanks!
       
      Lucas

    • By BAKED
      There are several threads on requesting BIOS modifications here on T | I but I thought another one wouldn't hurt.
       
            Your request should look like:
      Brand Model Type of modification(For example: Unlocked, added support, Logo, microcode, ME firmware etc  
      I'll respond as soon as I have time as I'm also currently working on other projects(Requests by PM is also ok)
      If anyone else have the knowledge and time feel free to respond to requests 
       
    • By ElChuterRD
      Greetings, I have a p650rs and I have this little problem that I can not play in MRHYBRID mode, only if the charger is connected, and I do not see high quality videos or play if it is in discret mode, if the A / C is connected.
       
      Any idea what it could be?
       
      I have the latest version of Bios and ECF
      I've been looking for custom-made Vbios but I can not find anything.
      Thank you


×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.