By Axel de S
I have a GT72VR 6RE with G-sync MSI Laptop. Sadly the GPU is partially dead (artefacts all over the screen, crashes, windows detecting a damaged hardware etc...).
So I bought an other GTX1070 MXM on ebay, which was used in a Vortex G65 6RE before.
Sadly, when I plug the new GPU in the laptop, the laptop screen stays completly off, but i can use the HDMI port. So i though that I would just have to flash the vbios to the one I was using on the GPU that died, but I couldn't because of a mismatch betwen the PCI Device ID.
The new GPU ID is : 10DE 1BA1 - 1462 11AF and the previous GPU ID was :10DE 1BE1 - 1462 11AF
Pretty close right? but the A1 and E1 variation are fcking everything up. I've read that 1BA1 is for non G-sync and 1BE1 is for G-sync. I've also read that the G-sync variation is not part of the card but is an external part no on the GPU board.
So now I'm wondering what can I do : is there a way to force the vbios flash or to change the PCI ID ? I really need some help here. I'm no expert and I've try as much as I could. Maybe I need to do some vbios editing but I don't really know how to do it and what to do exactly to make this work.
Thank you very much for your help guys
alienware 15 r2 970m with i7-6700hq vbios request so i can overclock and mess with voltage.
BIOS version backup made with techpowerup GPU-z.
or can someone re direct me to one already made that will work? all links i find are dead, thanks.
By Kunal Shrivastava
Hi guys, I am the proud owner of a Clevo p775dm3-g notebook purchased from azom.systems (authorized Clevo reseller in India, Model rebranded as Azom Legion-17.3 inches). Here are my specs:
Core i7 7700 (non-K version): undervolted by 110 mv and turbo boost disabled in BIOS- machine uses prema mod BIOS.
GTX 1080: undervolted by 100 mv on all frequency steps using MSI afterburner voltage/frequency curve editor. clocks are untouched.
16 GB DDR4: Cant remember clocks.
1440p 120 Hz screen: No tinkering done to refresh rate.
CPU has been delidded and repaste has been done on both CPU/GPU dies with gallium based TIM-Coolaboratory liquid ultra if I recall correctly.
My issue is GPU hitting max temp limit of 90 degrees while playing DOOM and framerate drops from 110 avg to mid 60s-70s with horrible stuttering- this is thermal throttling for sure.
System was running beautifully after repaste at 86 degrees max/ 77 degrees average at 100 percent fan speed. A month later I decided to see how much further I could push the system and ended up undervolting the CPU/GPU and RAM even further. The RAM undervolting part didnt work as well as I'd hoped, and I ended up resetting the BIOS to undo everything and reapply the previous setting (-110 for CPU with turbo boost disabled.)
I noticed that immediately after BIOS reset, both my CPU and GPU temps were 5-10 degrees higher even with the undervolt/underclock applied. Also, I think the fans were a bit louder before I reset the BIOS which leads me to believe that for some reason the fans are now capped at 80% max fan speed. There doesnt seem to be a fan speed selector in the BIOS or anywhere else so I cant say for sure whether this is a fan related issue or something else.Before the reset I could override the BIOS setting and set the fans to 100% by pressing fn+1, could I have done something to that setting after resetting the BIOS ? I dont think I have damaged the CPU or GPU as temps are holding fairly steady at 90-91 degrees and laptop doesn't shut down while gaming.
If I have overlooked something or if anyone reading this has any solution help would be greatly appreciated.
All settings/drivers/windows version/app version are exactly the same before and after BIOS reset.
I have been attempting to change my boost clocks values for the longest time, though I've been unsuccessful. I managed to flash my modded BIOS, though no changes seem to have had happened, along with no errors either. Here's all the stuff I used and was able to get. If someone is able to help me with this, it would be greatly appreciated.