tch150 Posted January 3, 2016 Share Posted January 3, 2016 Hi! Here is the picture taken from my k5000m. Obviously, the vbios eeprom is the same as your: MX25L2006E Should I shortcut pin1(CS) with pin4(GND) or pin1(CS) with pin8(VCC) to bypass the POST gpu check? And by the way, I still don't know which version of vbios works with my Clevo P150hm... It would be great if you write a tutorial for us, much appreciated! P.S.: Sorry for the pixel quality, I'm allowed to upload only pictures < 1MB! Quote Link to comment Share on other sites More sharing options...
Guest Posted January 4, 2016 Share Posted January 4, 2016 There is no stock K5000M vBIOS that works on HM...PM me in case you can get the system to a state where you could actually flash the card Quote Link to comment Share on other sites More sharing options...
kaxen Posted January 4, 2016 Share Posted January 4, 2016 2 hours ago, Prema said: There is no stock K5000M vBIOS that works on HM...PM me in case you can get the system to a state where you could actually flash the card boss, can you help me made vbios for clevo k3000m? I am able to boot into window after 3 beeps. thank you so much. Quote Link to comment Share on other sites More sharing options...
io____ Posted January 6, 2016 Share Posted January 6, 2016 Hey, it is pins 1 and 4, chip select and GND. Just shortcut them before turning on. This is my howto as is.. work in progress blind flash.zip tch150 can you PM me an high res picture of the chip? that would be a nice add on for the howto. (mine is SMD package) Quote Link to comment Share on other sites More sharing options...
tch150 Posted January 15, 2016 Share Posted January 15, 2016 On 4/1/2016 at 1:14 AM, Prema said: There is no stock K5000M vBIOS that works on HM...PM me in case you can get the system to a state where you could actually flash the card Thanks! I surely will pm you if i succeed in making it boot to dos. Quote Link to comment Share on other sites More sharing options...
tch150 Posted January 15, 2016 Share Posted January 15, 2016 On 6/1/2016 at 3:43 PM, io____ said: Hey, it is pins 1 and 4, chip select and GND. Just shortcut them before turning on. This is my howto as is.. work in progress blind flash.zip tch150 can you PM me an high res picture of the chip? that would be a nice add on for the howto. (mine is SMD package) Hi again! Sorry for my late reply, I still haven't have time to test and take another picture yet. I'll do it as soon as possible in my leisure time. By now, my profile doesn't allow me to download the attached file. Thanks again for the tips! Quote Link to comment Share on other sites More sharing options...
tch150 Posted January 29, 2016 Share Posted January 29, 2016 So, I've tried io____ 's tips, it works! I can blind type some commands in dos and backup the vbios, but the flash failed at the end, I got this error: ERROR: Update aborted Exit Code: 2 At the beginning, I heard 3 beeps then 2 beeps, and then almost 2 beeps. What does that mean? what's wrong with the command: nvflash -L log.txt -4 -5 -6 k5000m.rom or nvflash -i0 -4 -5 -6 k5000m.rom Should I type y or Y or yes or YES? (nvflash v5.163 dos) Thanks for helps! nvflash --list Quote NVIDIA Firmware Update Utility (Version 5.163) NVIDIA display adapters present in system: <0> Quadro K5000M (10DE,11BC,1558,0000) H:--:NRM B:01,PCI,D:00,F:00 nvflash --check Quote NVIDIA Firmware Update Utility (Version 5.163) Adapter: Quadro K5000M (10DE,11BC,1558,0000) H:--:NRM B:01,PCI,D:00,F:00 The display may go *BLANK* on and off for up to 10 seconds during access to the EEPROM depending on your display adapter and output device. Identifying EEPROM... EEPROM ID (20,0000) : Unknown nvflash -L log.txt -4 -6 k5000m.rom Quote *** NVFLASH LOG FILE *** Version 5.163 Command: flash FindDevices: Device:00:00:00=8086:0104:1558:7100 Device:00:01:00=8086:0101:1558:7100 Device:00:16:00=8086:1C3A:1558:7100 Device:00:1A:00=8086:1C2D:1558:7100 Device:00:1B:00=8086:1C20:1558:7100 Device:00:1C:00=8086:1C10:1558:7100 Device:00:1C:01=8086:1C12:1558:7100 Device:00:1C:02=8086:1C14:1558:7100 Device:00:1C:03=8086:1C16:1558:7100 Device:00:1D:00=8086:1C26:1558:7100 Device:00:1F:00=8086:1C49:1558:7100 Device:00:1F:02=8086:1C03:1558:7100 Device:01:00:00=10DE:11BC:1558:0000 GPU Device:01:00:01=10DE:0E0A:1558:0000 Device:02:00:00=1033:0194:1558:5102 Device:03:00:00=197B:0250:1558:7100 Device:03:00:01=197B:2392:1558:7100 Device:03:00:02=197B:2391:1558:7100 Device:03:00:03=197B:2393:1558:7100 Device:04:00:00=168C:0030:103C:1627 Device:05:00:00=197B:2380:1558:7100 One to one mode Testing adapter: Quadro K5000M (10DE,11BC,1558,0000) H:--:NRM B:01,PCI,D:00,F:00 Action: Read image head. Action: Identify EEPROM. Atmel Serial EEPROM Identify. Reported Manufacturer Code (JEDEC): C2 Reported Device Code (JEDEC): 2012 EEPROM ID (C2,2012) : MX MX25L2005 2.7-3.6V 2048Kx1S, page Action: Read EEPROM image. Reading EEPROM bytes. Start: 0x00000000 Count: 4096 Read complete. Testing Image: k5000m.rom IFR image mode Mismatch Type: Computed: 0x0000010A WARNING: Firmware image PCI Subsystem ID (10DE.0000) does not match adapter PCI Subsystem ID (1558.0000). Overriding PCI subsystem ID mismatch Mismatch Type: Adjusted: 0x00000000 Current - Version:80.04.67.00.07 ID:10DE:11BC:10DE:0952 GK104 Board - 2051b503 (Normal Board) Replace with - Version:80.04.12.00.03 ID:10DE:11BC:10DE:0000 GK104 Board - 2051b503 (Normal Board) ERROR: Update aborted Exit Code: 2 Quote Link to comment Share on other sites More sharing options...
tch150 Posted January 29, 2016 Share Posted January 29, 2016 (edited) Yeah! I've finally got the card K5000m flashed! I've tried many times with nvflash different combination options commands, and then suddenly heard a beep, so I backup the vbios to verify whether it has been changed. And.... YES! Now I get into Windows without problem, have to find the correct driver now! I'll be back for more info later! Thanks you very much io____ !! and all others! Edited January 29, 2016 by tch150 Quote Link to comment Share on other sites More sharing options...
tch150 Posted February 2, 2016 Share Posted February 2, 2016 (edited) I still canno't upload the original picture, so I just keep the image of the chip. On 6/1/2016 at 3:43 PM, io____ said: On 6/1/2016 at 3:43 PM, io____ said: Hey, it is pins 1 and 4, chip select and GND. Just shortcut them before turning on. This is my howto as is.. work in progress blind flash.zip tch150 can you PM me an high res picture of the chip? that would be a nice add on for the howto. (mine is SMD package) Hey, it is pins 1 and 4, chip select and GND. Just shortcut them before turning on. This is my howto as is.. work in progress blind flash.zip tch150 can you PM me an high res picture of the chip? that would be a nice add on for the howto. (mine is SMD package) Edited February 2, 2016 by tch150 Quote Link to comment Share on other sites More sharing options...
tch150 Posted February 2, 2016 Share Posted February 2, 2016 (edited) On 4/1/2016 at 1:14 AM, Prema said: There is no stock K5000M vBIOS that works on HM...PM me in case you can get the system to a state where you could actually flash the card My vbios's size is 88KB, and I've changed an inf file from nvidia's latest driver, then do a manual install from inf file cause I just couldn't run setup.exe. The clock frequency is a bit low, I'll change it later, any advices? Thanks! Edited February 2, 2016 by tch150 Quote Link to comment Share on other sites More sharing options...
io____ Posted May 2, 2016 Share Posted May 2, 2016 Hallo everybody.. so nice to see that this worked out for others too, the card is running just fine and I d say a bit too cool, so how to squeeze out some extra clocks here? With Invidia Inspector I can just get a 315MHz increase maxing out at 750MHz. Is there a mod to unlock the card? tx Simone Quote Link to comment Share on other sites More sharing options...
OldHary Posted July 18, 2017 Share Posted July 18, 2017 Hello everybody, im new in this Forum and wanted to ask for help. I got an old Clevo p150hm with a bricked hd6990m. Now i replaced it with a msi gtx570m 3gb, and i got windows working, but the card is not shown in the Bios and i cannot install the card. I searched a lot but i am affraid of flashing and bricking the card. There is no clevo vbios for a 570m and also there is just a vbios for gtx670m with 1,5gb. What do i have to do now? Quote Link to comment Share on other sites More sharing options...
io____ Posted July 20, 2017 Share Posted July 20, 2017 I am not sure about what you have to do now, have you read thoroughly this thread? There is everything you need to know about flashing cards but if you haven't got the proper vbios.. Quote Link to comment Share on other sites More sharing options...
TNNotebooks Posted September 2, 2017 Share Posted September 2, 2017 (edited) On 28.4.2015 at 1:51 PM, Prema said: You need a special Mod if you want to use that card on HM...PM me. Hallo , i have a Problem with a Clevo P170HM - i want to Install a GTX670MX pulled from a Medion. Original VBIOS of that card is 80.04.5B.00.A5 ( M_backup.rom by nvFlash and GTX670MX original VGA BIOS.rom by GPUZ Dump ) System booted to Windows but NVIDIA Driver van not be installed and Card is shown als Standard Adapter. So i flashed the Clevo 670mx - 3GB - 80.04.58.00.03 - 'OC edition'_rev2 and now Notebook have Start screen and 2 Beeps but do not Boot to Windows any more -- same like posted here. Actual Status : I desoldered the BIOS Chip , Reprogrammed with the Original VBIOS of that card 80.04.5B.00.A5 on a external Programmer and soldered the Chip to the Card. Now Windows is starting as Standard VGA Adapter again. Can you help me with a Compatible File Too ??? Or do i only need a Mod Driver ? Do you have a moded Driver ? or how i have to Mod a Driver ? How can i PM you here ? Thank you very Much in Advance Thomas GTX670MX original VGA BIOS.rom M_backup.rom Edited September 3, 2017 by TNNotebooks Quote Link to comment Share on other sites More sharing options...
TNNotebooks Posted September 14, 2017 Share Posted September 14, 2017 Problem Solved System Infos Prior PCI\VEN_10DE&DEV_11A1&SUBSYS_00001558&REV_A1 PCI\VEN_10DE&DEV_11A1&SUBSYS_00001558 PCI\VEN_10DE&DEV_11A1&CC_030000 PCI\VEN_10DE&DEV_11A1&CC_0300 Der Prozess zum Installieren von Treiber display.inf_amd64_d52ffbbc7f640691\display.inf für Geräteinstanz-ID PCI\VEN_10DE&DEV_11A1&SUBSYS_00001558&REV_A1\4&38EC51A5&0&0008 wurde mit folgendem Status beendet: 0x0. Action : Driver Unziped C:\NVIDIA\DisplayDriver\385.41\Win10_64\International Infos How to MOD : http://null-bin.blogspot.de/2015/08/how-to-modify-nvidia-notebook-driver.html Action : nvcvi.inf mofified : 3 Lines added [NVIDIA_Devices.NTamd64.10.0...14310] %NVIDIA_DEV.11A1.0000.1558% = Section030, PCI\VEN_10DE&DEV_11A1&SUBSYS_00001558 [NVIDIA_Devices.NTamd64.10.0] %NVIDIA_DEV.11A1.0000.1558% = Section029, PCI\VEN_10DE&DEV_11A1&SUBSYS_00001558 [Strings] NVIDIA_DEV.11A1.0000.1558 = "NVIDIA GeForce GTX 670MX" Go to Winwows programs Windows system CMD Window Run the prompt as an administrator Type cd.. cd .. to get into the root net user Administrator / active: yes Bcdedit.exe -set TESTSIGNING ON Reboot the device and log in as a user administrator. Right below should now Shown : test mode Win10 Pro build ...... Go to NVIDIA folder in mainroot of C C: \ NVIDIA \ Display Driver \ 385.41 \ Win10_64 \ International Run the setup as an administrator (right click) Now install drivers and to the question "is not signed" still install. After the installation in the CMD Window net user Administrator / active: no Bcdedit.exe -set TESTSIGNING OFF Then close the prompt and reboot normally Quote Link to comment Share on other sites More sharing options...
alex.forencich Posted November 10, 2017 Share Posted November 10, 2017 (edited) On 1/29/2016 at 2:57 PM, tch150 said: Yeah! I've finally got the card K5000m flashed! I've tried many times with nvflash different combination options commands, and then suddenly heard a beep, so I backup the vbios to verify whether it has been changed. And.... YES! Now I get into Windows without problem, have to find the correct driver now! I'll be back for more info later! Thanks you very much io____ !! and all others! Where did you get the ROM from? I presume it's from prema's website, but that appears to be totally borked right now. Could you possibly post the file here, or PM it to me, if you still have it? Edited November 10, 2017 by alex.forencich Quote Link to comment Share on other sites More sharing options...
ikky_phoenix Posted July 7, 2019 Share Posted July 7, 2019 @PremaDo you have this 670mx vbios for the p150hm/p170hm? Quote Link to comment Share on other sites More sharing options...
Mar1XO Posted July 21, 2019 Share Posted July 21, 2019 i dont know if you solved this or not but try to update to the lastest bios and flash a modded vbios for the card Quote Link to comment Share on other sites More sharing options...
ikky_phoenix Posted November 3, 2019 Share Posted November 3, 2019 On 7/21/2019 at 7:16 PM, Mar1XO said: i dont know if you solved this or not but try to update to the lastest bios and flash a modded vbios for the card My problem is i can't download the modded vbios from this site, i don't know what i have to do. The laptop bios is it's lastest version. Sorry for the late reply. Quote Link to comment Share on other sites More sharing options...
Bios Modder Klem Posted November 3, 2019 Bios Modder Share Posted November 3, 2019 26 minutes ago, ikky_phoenix said: My problem is i can't download the modded vbios from this site, i don't know what i have to do. Hi! You can read the forum rules: https://www.techinferno.com/index.php?/announcement/4-user-account-promotion-rules-read-before-posting/ Quote Link to comment Share on other sites More sharing options...
ikky_phoenix Posted November 5, 2019 Share Posted November 5, 2019 On 11/3/2019 at 9:36 AM, Klem said: Hi! You can read the forum rules: https://www.techinferno.com/index.php?/announcement/4-user-account-promotion-rules-read-before-posting/ Thanks! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.