Jump to content
Steve135

M18x R1 SLI Cable Setup

Recommended Posts

So I just made the transition from red to green with my R1 and had a slight issue with the new SLI cable. In order to make it work it had to be routed over both GPU heatsinks, whereas the old crossfire cable was designed to fit over the palm rest, making right angles around the heatsinks. I placed some camera lens cleaning cloths between the cable and the heatsinks to provide some separation and just sticky taped them in place. I'm hoping this setup will work.

Has anybody else experienced a situation like this? Do you recommend me keeping it this way or should I search for a SLI cable that has the right angles in it to go around the heatsinks?

Cheers,

post-32156-14494999432136_thumb.jpg

Share this post


Link to post
Share on other sites

I had the same SLI cable setup when I owned the M18x-R1 and it was fine. You've got nothing to worry about.

Share this post


Link to post
Share on other sites

I did read a while back that the crossfire cables from Nvidia were failing due to the heat being transferred into the cable. I did a mod once with some thermal strips placed under the cable to keep it from becoming too warm ! Might be worth doing if you are worried :)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By ounces
      After spending significant time and effort to obtain "DC" screen for 8770w (which is essentially a regular IPS panel with fancy board that converts 8bpc LVDS to 10bpc DP), I have finally got and installed one. All works great, except of the one problem...

      It has pretty bad banding / posterization in lower shadows. I have tried profiling it in different modes (full range, sRGB, rec709) - issue persists, and it indeed shows only in the lowest part of the characteristic curve. Mids and highlights are represented fine and show low deviation from reference values.

      GPU is HP K4000M, Nvidia drivers installed "as it is", video-card is identified without a hitch.
      Banding was not present with the original TN panel using the same GPU.
       
      While checking a software side, I have noticed that Win10 has bit depth set to 8-bit...
       

       
      My initial reaction was, - "Easy, let's change it in `nvidia-settings` and we're all set":

      ...but that would be too easy, right? After selecting 10bpc and clicking "Apply" screen went off and back on, only to show that depth stayed at 8bpc. Repeating the above few times yielded exactly the same result and I'm not in a hurry to meet a cliched (and laymen) definition of insanity.
       
      Let's check GPU-Z. So far so good, nothing unusual. Notice the highlighted BIOS version and subvendor string:
       
      Time to delve into other tabs. We are running WDDDM v2.4 which supports GPU dithering, but hey... BIOS version has changed!
       
      Briefly back to `nvidia-settings` to check what is reported by vendor's own utility:

       
      So far, we have two strings for BIOS version:
      80.04.5A.00.02 (let's call it an "A") 80.4.33.0.37 (let's call it a "B")  
      Notice how 2nd one seems to not follow hexademical notation. Lastly, "NVIDIA BIOS" drop-down, reports "A" version:
       
      ...and monitor section which confirms that rig is indeed capable of 10bpc, but currently running at mere 8bpc:

       
      Windows "Adapter settings", reports version "B". It's 2019, diversity is a must.

       
      "NVidia inspector" is of the same opinion:

       
      Now, let's use some seriously legit tools and check-in exported BIOS file in `nvflash`:

       
      Here we have two three interesting findings:
      Reported vendor is Dell, not an HP. See this link for details. BIOS version is back to "A". Have I already mentioned diversity? MXM module uses MX25L2005 flash storage in WSON-8 packaging. If things go real nasty, we should be able to rescue a patient via Pomona clip and external programmer.  
      Loading the same file in "Kepler BIOS tweaker" confirms the facts:

       
      EDID settings, courtesy of NVidia Control Panel. Hex dump can be found at the bottom of this post.
      ...Shall I be worried about "60.02Hz" refresh rate?
       
      To summarize:
      Why two different BIOS versions are reported? Anything to do with UEFI (e.g. HP is sideloading its own during boot)?.. Why two different vendors reported? As far as I remember, this is branded HP GPU. Where to get "clean" BIOS of K4000M for future experiments? Ideally from 8770w equipped with "DreamColor" panel from a factory.  
      Link to the dumps, BIOS ROM and monitor EDID: https://mega.nz/#F!zGgRmQIL!9q2QFZtHuK2RQ-WHXMA4Mg (also attached to this post)
      K4000M.zip
    • By Blocker35
      Hi guys, bit of a rookie to the whole EGPU scene. Currently I have:
       
      - MacBook Pro 2015 13inch (3.1GHz Core i7 16GB RAM)
      - Razer X Core 
      - Apple TB3 to TB2 Adapter
      -  TB2 Cable (Cable Matters)
      - 23inch AOC External Monitor
       
      I am wonder about what graphics card to get to run X-Plane11 with high graphic settings?
      I have purgewrangler set up and ready to use with an AMD graphics card, but am also open to the idea of an Nvidia graphics card.
      Any advice appreciated. I did not buy a Windows PC as I need a Mac for various other things and wanted an all-in-one laptop.
    • By GrisGris
      For when that rubber coating on your laptop phase shifts to fly paper...
       
      Here is what I did,
       
      Disassemble M18x:
      Well documented by debaucher:
      The palm rest section was the biggest offender for me;

      >I used a plastic spoon and nail polish remover to remove the rubber coating:
      >Obviously remove as many of the various utility boards as possible.
      >I left the touch pad in place because this model used thermally fused plastic rivet like pieces to hold the light pipes in place and I found it easier to mask it off.
      >"FrogTape Delicate Surface" worked very well for masking off various surfaces

      >I used Krylon Plastic Paint as a base coat and 'Jet Black metal flake Automotive Paint;

      >With the paint still setting up I dusted various glow powders over the substrate and dusted some additional black paint to achieve some depth to the effect .
      >I after the automotive paint set up I use mate clear coat the overcoat the entire surface. I personally believe glossy clear coat would not look as good. 
      >Adjust as needed and re-assemble.

      >I Used a USB LED clamp light available ebay/amazon $10 to illuminate
       
      Hope you enjoyed the first post...
      .
    • By Kel
      I got the exp gdc beast 8.5 got all the connections right... laptop boots up... fans turn on the gpu.... device manager detects gtx 1060 with a “ ! “ in a yellow triangle. Now what to do.... i tried to do the bios mod.... but realised that i have 3.07 version. 
      Questions-
      1 is there any way to get this done without the mod?? 
      2 if mod is the only way... kindly help me with step by step instruction in laymans terms... i m not a techy... so i might not understand technical terms.... altho i am interested... but learning yet. Please help. 
    • By thechillhacker
      Hello all
       
      I have a Clevo P370EM3 laptop with a pair of GTX 680Ms in SLI mode and have never been able to get Linux to work properly with full acceleration and without tearing. I have tried every xorg config I can find, and even all the modifications from the nvidia configurator to no avail. Has anyone been able to get these things to work 100% in Linux? I have typically used ubuntu based distros, including Mint, and every available driver version from the repositories, but can never get it to work quite right.
       
      Thanks for any help anyone can provide. It is killing me to run Windows on this machine because of these issues, and I am almost to the point of installing the inferior 7970 cards.
       
      Have a great day
      -TCH
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.