Jump to content
EwinRacing Flash Series Gaming Chairs
svl7

NVIDIA Maxwell VBIOS mods - 900m series overclocking versions

Recommended Posts

On 4/27/2020 at 7:07 PM, Klem said:

Ok. Check PM.

Check pm :)

Share this post


Link to post
Share on other sites
3 minutes ago, Norby said:

Check pm :)

Hi!

Previous PM conversation was deleted. So I didn't received any new message from you. But you can create new PM conversation.

Share this post


Link to post
Share on other sites

Hi, Klem, I have vBIOS modded and undervolted but temperature is too high yet. Could you help me with a new one?

 

https://ibb.co/cX4NT5h (My Nvidia inspector screenshot)

 

I hope that rom file had been loaded successfully. Edit: https://we.tl/t-PeN8N4ff42

 

Thanks in advance.

 

 

Edited by Ganzuas

Share this post


Link to post
Share on other sites
8 hours ago, Ganzuas said:

Hi, Klem, I have vBIOS modded and undervolted but temperature is too high yet. Could you help me with a new one?

Hi!

No, I make vBIOS to increase the possibility of overclocking a graphic card, but not to lower temperature, and not to undervolting. So, I can't help in your case. Sorry.

Share this post


Link to post
Share on other sites
14 hours ago, Klem said:

Hi!

No, I make vBIOS to increase the possibility of overclocking a graphic card, but not to lower temperature, and not to undervolting. So, I can't help in your case. Sorry.

Ok, Thanks anyway.

Share this post


Link to post
Share on other sites

Hi @Klem,

 

Would you help me with this?

I have replaced amd8970m to Nvidia gtx970m 6GB.I have bought it from ebay, it was originally on Clevo P370SM-A, and I have laptop Clevo P150SM-A.imageproxy.php?img=&key=f8850ecfbcdddcc4 Bios version 1.03.09,  KBC/EC version 1.03.08

Vbios version 84.04.48.00.21, Device ID 10DE 1618- 1558 5281 Laptop bios does not recognises card, and Device ID is not on the inf list. W10 drivers install unsucsesfull, managed to get it on W7, but apps requiring Nvidia card not working.

Can this card be reflashed to work on my laptop?

Could upload images, but not allowed.

Thanks for your help, give a shout if you need more info.

Edited by asteroidb

Share this post


Link to post
Share on other sites

Hi Clem, I want to remove the limit at +135 and unlock the voltage on my MX 110. What do I need for this?

Share this post


Link to post
Share on other sites
9 hours ago, belkin said:

Hi Clem, I want to remove the limit at +135 and unlock the voltage on my MX 110. What do I need for this?

Hi!

What the laptop model?

Share this post


Link to post
Share on other sites
2 hours ago, Klem said:

Привет!

Какая модель ноутбука?

Asus vivobook x540ubr

Share this post


Link to post
Share on other sites
17 minutes ago, belkin said:

Asus vivobook x540ubr

Post here your bios backup and your screenshot in Nvidia Inspector utility (full window with overclocking sliders). I'll take a look.

For creating backup of bios you can use attached backup tool. Extract attached archive directly on the Desktop and run backup tool as Administrator (right click mouse). Program will create archive "results" directly on the Desktop. Post here this archive "results" or upload it into any fileserver and post the link.

https://www.sendspace.com/file/bhbprh

 

or

 

https://files.fm/u/qyf9r9c2

 

Share this post


Link to post
Share on other sites
27 minutes ago, Klem said:

Post here your bios backup and your screenshot in Nvidia Inspector utility (full window with overclocking sliders). I'll take a look.

For creating backup of bios you can use attached backup tool. Extract attached archive directly on the Desktop and run backup tool as Administrator (right click mouse). Program will create archive "results" directly on the Desktop. Post here this archive "results" or upload it into any fileserver and post the link.

https://www.sendspace.com/file/bhbprh

 

or

 

https://files.fm/u/qyf9r9c2

 

I can’t get my BIOS using gpu-z and other programs, it says that my BIOS is unreadable. I can only give bios from the official site 

https://drive.google.com/open?id=1ytq5AzBx87BRA8l2yJcgx8rybflD5JJE - picture 

https://drive.google.com/open?id=1vsMvrllJpCT1xutSVx6C9ByZue05POyA bios

Share this post


Link to post
Share on other sites
4 minutes ago, belkin said:

I can’t get my BIOS using gpu-z and other programs, it says that my BIOS is unreadable.

For creating backup of bios you can use attached backup tool. Extract attached archive directly on the Desktop and run backup tool as Administrator (right click mouse). Program will create archive "results" directly on the Desktop. Post here this archive "results" or upload it into any fileserver and post the link.

https://www.sendspace.com/file/bhbprh

 

or

 

https://files.fm/u/qyf9r9c2

 

 

4 minutes ago, belkin said:

I can only give bios from the official site 

I don't need it.

Edited by Klem

Share this post


Link to post
Share on other sites
12 minutes ago, Klem said:

For creating backup of bios you can use attached backup tool. Extract attached archive directly on the Desktop and run backup tool as Administrator (right click mouse). Program will create archive "results" directly on the Desktop. Post here this archive "results" or upload it into any fileserver and post the link.

https://www.sendspace.com/file/bhbprh

 

or

 

https://files.fm/u/qyf9r9c2

 

 

I don't need it.

I do not understand your message, I am not a native speaker of English, I do not know it well. Here is a link to the results 

https://drive.google.com/open?id=1wt72xqTB3GPTdyOhDUKL5R5NcDJYliXM

Share this post


Link to post
Share on other sites
1 hour ago, belkin said:

I do not understand your message, I am not a native speaker of English, I do not know it well. Here is a link to the results 

https://drive.google.com/open?id=1wt72xqTB3GPTdyOhDUKL5R5NcDJYliXM

Well, I checked your bios, it's protected against write any modified/unlocked bios.

In this case only two ways:

1. We can try to disable this protection.

2. You will need to flash unlocked bios with hardware SPI programmer (like CH341A).

Share this post


Link to post
Share on other sites
5 minutes ago, Klem said:

Ну, я проверил ваш BIOS, он защищен от записи любых модифицированных / разблокированных BIOS.

В этом случае только два пути:

1. Мы можем попытаться отключить эту защиту.

2. Вам нужно будет прошить разблокированный BIOS с помощью аппаратного SPI-программатора (например, CH341A).

"Try to unlock" and "flash the programmer" are two different things? If so, am I risking anything when trying to unlock?

Share this post


Link to post
Share on other sites
5 minutes ago, belkin said:

"Try to unlock" and "flash the programmer" are two different things?

Please, read my previous post carefully. I wrote:

"... In this case only two ways:

1. We can try to disable this protection.

2. You will need to flash unlocked bios with hardware SPI programmer (like CH341A)."

 

5 minutes ago, belkin said:

If so, am I risking anything when trying to unlock?

No, but method may be too difficult for you.

Edited by Klem

Share this post


Link to post
Share on other sites
8 minutes ago, Klem said:

Пожалуйста, внимательно прочитайте мой предыдущий пост. Я написал:

«... в этом случае только два пути:

1. Мы можем попытаться отключить эту защиту.

2. Вам нужно будет прошить разблокированный BIOS с помощью аппаратного SPI-программатора (например, CH341A). "

 

Нет, но метод может быть слишком сложным для вас.

if I really do not risk getting a "dead" laptop, then I agree to try to unlock. I don’t think that it will be very difficult for me. What is needed for this?

Share this post


Link to post
Share on other sites
18 hours ago, belkin said:

if I really do not risk getting a "dead" laptop, then I agree to try to unlock. I don’t think that it will be very difficult for me. What is needed for this?

Ok, download attached archive.

Extract it directly on Desktop.

Format any USB flash drive into FAT32, then put the folder EFI to the your already formatted USB flash drive. 
It should create a folder structure like this:

F:\EFI\BOOT\BOOTX64.EFI

 

Go in bios setup menu, search and disable "Secure Boot" option.

Then plug created USB flash drive into laptop and try to boot laptop from USB flash drive.

If you did all things correct, then you should see a message saying something like:


Code:
Welcome to GRUB!
Entering rescue mode...
error: file not found
grub rescue>

 

Edited by Klem

Share this post


Link to post
Share on other sites
1 hour ago, Klem said:

Ok, download this archive:  https://files.fm/u/ffuer35v

Extract it directly on Desktop.

Format any USB flash drive into FAT32, then put the folder EFI to the your already formatted USB flash drive. 
It should create a folder structure like this:

F:\EFI\BOOT\BOOTX64.EFI

 

Go in bios setup menu, search and disable "Secure Boot" option.

Then plug created USB flash drive into laptop and try to boot laptop from USB flash drive.

If you did all things correct, then you should see a message saying something like:


Code:
Welcome to GRUB!
Entering rescue mode...
error: file not found
grub rescue>

 

Am I doing something wrong? Writes to press tab after clicking this happens. What am I doing wrong? here the photo for some reason does not load, here are the links 

https://drive.google.com/open?id=10QEOcp_3B_ZBMVbMgMys7k9kX0yBgJml  

https://drive.google.com/open?id=12vNhNHLUSd4l9Kz34qTh7guzqon2BBvj

Edited by belkin

Share this post


Link to post
Share on other sites
2 minutes ago, belkin said:

Am I doing something wrong? Writes to press tab after clicking this happens. What am I doing wrong?

Post screenshot.

Share this post


Link to post
Share on other sites
2 minutes ago, Klem said:

Post screenshot.

photos by links, I can’t upload here, it gives an error ...
If it is important, I can try to upload to the forum again

Share this post


Link to post
Share on other sites
2 minutes ago, belkin said:

photos by links, I can’t upload here, it gives an error ...
If it is important, I can try to upload to the forum again

I don't see your link.

Share this post


Link to post
Share on other sites
6 minutes ago, belkin said:

On screenshot all looks like ok.

Now that you have the GRUB console, you need to enter the following two commands:

setup_var 0x963 0x0


setup_var 0xF66 0x0

 

After each command press Enter button.

Please note: Your system may seem to lockup after you enter each of these commands. The first setup_var may never seem to finish.
Give it a few minutes and if nothing happens, force-reboot the machine and redo step 4 to get back to the GRUB console.
Once there, enter the second setup_var command and allow the same to happen. If nothing happens again, just give it a few minutes then force restart the machine.

After you have done both of these commands restart the machine and boot into Windows as normal.

Then run backup tool again, and send me new "results".
 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By IveGotRoot
      I have recently upgraded my laptop(an M6800 firepro 6100) and replaced it with an GTX 980m. Nvidia says that the latest driver(461) supports my card but i can only install up to 388.13 Ive tried to mod it but i can't figure it out. I can run the latest linux driver tho
    • By Freddyicy
      I have spent a little time in the past few days looking around this site. I would love for someone to point me in the right direction to a forum that has information that could help me out with my problem.
       
      I have a:
       
      Alienware M17XR3 
      Windows 7 Home Premium 64-bit
      Intel I7-2820QM 2.3
      Bios InsydeH20 Version 1.0 A12
      NVIDIA GeForce GTX 460M
      (4x) 4 GB Ram
      samsung 2.5" 256 SSD (SATA3.0Gbps)
       
      It has been an amazing machine for the last 10+ years. Minor issues, nothing that an Alien Respawn could not fix, till now! On battery power it works just perfect.  Then I plug it in and it's all OK until I try to do anything, and then the screen goes white. The screen sometimes goes yellow, sometimes blue, but mostly white screen. It will do nothing until I do a hard reset (holding the power button till it turns off and turn it back on) with the power unplugged.  If the power is not unplugged then it will go through boot up to windows swirling dots then go white again. If I plug it in and do nothing I can charge it, unplug and continue what i was doing. I have tried a lot of solutions bouncing around the internet, and thought I was having a DC Jack connection issue (replaced the ac/dc power adapter, then the motherboard). I get a better connection now but with the same white screen result. I stumbled into this forum and I'm hoping to find solutions to my issues.  Then upgrade like so many others have.
       
      Any ideas, comments or suggestions welcome.
       
      Thank you in advance!
       
    • By MitjaStachowiak
      Hello,
      does anyone know, which is the chip holding the VBIOS-ROM on an AMD Pro-WX 7100?
       
      I've two AMD Pro WX 7100 which doesn't work. One has maybe a wrong VBIOS and gets deativated in BIOS before any system boots. The other one is not recognized by the MB so I suspect this one to be defective and un-soldered two chips, which I suspect to be the VBIOS-ROM:
       

       
      On earlier GPUs, the VBIOS was the chip closer to the GPU. But here, this chip has a bottom SMD contact which looks more like some power electronics...
      So before I start soldering on the probably working GPU - can you tell me, which actually is the VBIOS?

      Thanks.
       
       
    • By pippocarlot
      Hello everyone! I am looking for an answer to a problem I cannot find a solution to ... I purchased an Amd wx 4150 MXM GPU module su e bay to upgrade my HP 8570W Mobile Workstation which is currently equipped with a Fire Pro M4000. Once the new GPU has been installed, the PC screen no longer turns on but works only with external monitors connected via the docking station. The same happens once the drivers are updated! If I put the old card back on, the integrated monitor starts working again ... How can I fix it?
    • By Swick1981
      Bios Release Version – v2.0.0
       

       
      Updated or Modded Items:
      A11 UNLOCKED BIOS FOR m18Xr2 (UNLOCKED BY SVL7 AND FULL CREDIT GOES TO HIM FOR UNLOCKING!)
      SVL7 Also created the PRR2.EXE tool that allows you to flash the new bios by unlocking it.  (FULL CREDIT GOES TO HIM FOR THAT FILE PRR2.EXE)
       
      Here are ALL the things I've added, modded, and enhanced on this bios -
      I've added FULL LEGACY SUPPORT ON THIS BIOS with ONE or TWO CARDS (SLI).  You can FINALLY use Win 7 OS on your machine and run the 900 series GPU's! 
      This is a MAJOR breakthrough!
       
      LEGACY SUPPORT Confirmed.  Works with 900 series GPu's in single OR SLI formation Updated the Intel RST Legacy to v12.9.0.2006 (Supports TRIM in RAID0 - CONFIRMED) Updated Intel RST UEFI to v12.9.0.2006 (Supports TRIM in RAID0 - CONFIRMED) Updated the ONBOARD Video Card for the HD3xxx to v2171 - FROM v2132 Updated ONBOARD Video Card for the HD4xxx to v2171 - FROM v2132 Updated the LAN Firmware & PXE Boot from 2.0.5.9 to v2.0.6.6 ADDED NvMe Support for m18xr2 ADDED M.2 support for m18xr2 Updated CPU Microcode to v29 for the 2900 CPU's Updated CPU Microcode to v1c for the 3900 CPU's Updated GOP Driver for Intel Sandy Bridge CPU Updated GOP Driver for Intel Ivy Bridge CPU Updated MAIN GOP Policy module for the m18xR2 Eliminated some code that wasn't used in the m18xR2 Updated CSM Module (v2) Streamline some coding to make mod(s) run a little more efficiently (v2) Added FPARTS.TXT to rar file in v2. (I had forgot to add it in v1) v2.5 to be released shortly.  I've updated a few more modules that I didn't realize could be updated.  (It's only 3 modules, but it's still an update!)   It should be released in about a week.  Hope this helps ya'll!  
      Instructions to flash:
      Use a flash drive to create a boot disk into dos Unzip ALL files into the root of the flash drive (flash.bat, r2final.bin, fpt.exe, flash.bat, prr2.exe, fparts.txt,m18r2.hdr, m18r2.hdr.bin, readmefirst.txt) BOOT INTO DOS – Note, that when you set the bios to legacy in order to boot into dos, you MAY have to reinstall OS!  (Just be prepared to reinstall no matter what) Once you boot into dos, run the file flash.bat It will unlock your bios (THANKS TO SVL7’s BIOS UNLOCKING TOOL – ALL CREDIT TO HIM FOR THIS TOOL!) Let it flash… Reboot your pc, and enjoy the MASSIVE updates!  
      Be on the lookout as I do plan to release newer version with more updates in the future.  However, it wont be for at least a few weeks as I'm now working on legacy support for the m17xR4 and several other systems.  So please be patient!
       
      ENJOY!
       
      Thread link for more information and discussion:
       
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.