Jump to content
mrthumb

Clevo P170SM upgrading.

Recommended Posts

Hi guys. I have a Clevo P170sm which come with a gtx 770m and now the time has come to put in a 780m. I have done some research into this and I installed the latest Prema bios mod. Thats all the preparation i done. I have thermal pads in the post.

Now, the 780m I got is this one from

New Nvidia GeForce GTX 780M 4GB DDR5 MXM 3.0 Type B for Clevo Alienware | eBay

Is there someone else out there who has done the same thing? Will i need special drivers or will i have to flash the graphics card now?

Thanks in advance. Tom.

Share this post


Link to post
Share on other sites

For those who have just seen this.

I installed the card, using the existing thermal pads as they were comparable.

I didn't even uninstall the old nvida driver. I just had to reboot once.

I did have to remove the old piece of metal on the back of the card that pulls the heatsink down and it was done carefully with a screw driver and a heat gun. take your time.

so all you need to do this is the prema mod bios!

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

normally, you dont need mod bios for upgrade to gtx 780m and the heatsink is the same, only themo pads you must fit exactly.

what is whit this card exaclty from link, i dont know.

when is from Clevo than this is no problem. from another brand, flashing.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Bullfrog098
      Hey everyone, just a question would anybody know where/how I could get a modded bios for a G75VW so I can get a 670MX to work in it? Any help would be appreciated!
    • By DgknGkdn
      The computer I used was '' Lenovo Y510P ''. There is a '' Nvidia GT755M [SLI] '' as a display card. I have tried both ways of downloading the video card driver from both GeForce Experience and Nvidia driver site. Both kinds of graphics cards are starting to update. Later, the 'graphic driver is installed' part of the screen goes and never comes again. I can not enter Windows when I turn off the computer. I have to take format from scratch.

      After formatting, Windows automatically loads a graphics card driver in 2017, trying to update the driver again, it stays black on the screen again. I have to format again.

      With DDU (Display Driver Uninstaller) program, I deleted the old video card driver and updated it again. But I met the same problem.

      I communicated with Nvidia and stated that I had such a problem. They asked me not to install the 388.13 video card driver. That graphics card driver has been loaded without any problems. But I have the same problem with all the video card drivers out there.
       
      NOTE: This problem only happens on Windows 10. I can update the display board without any problems in operating systems like Windows 8,8.1.
       
      NOTE: I have been having this problem for about 2 months, before I could update my display card in Windows 10 without a problem.

      The driver I am currently using is: 388.13
    • By TheShortStackTech
      I recently got a 2010 27" iMac for free! Some further research concluded that the MXM slot in the iMac has been proven to work with a GTX 880m, including Mac OS! I used to play with a 7970 ghz edition, but ended up selling it for some more projects. I've been lagging along on a 5870 2gb and thought that with my switch to the free iMac, I might as well update my gpu. Heres the problem I was faced with: the 880m is a little underpowered on stock clocks. So, after even more research I discovered that the 980m was around the same as a 7970 performance wise. I ended up grabbing a deal on an 880m for only 160$, but I did want to share my findings with you guys.
       
      *WARNING* ONLY 2009, 2010, AND 2011 IMACS HAVE THE MXM SLOT!!!! IF YOU ARE USING A 2012+ YOU CANNOT UPGRADE YOUR GPU
       
      So the 980m used to work all the way up to mac os sierra. It's now high sierra, but the fix is still pretty simple.
       
      What you will need:
      -thermal pads
      -copper ram heatsinks/ one of the specialized backplates that cools MXM memory modules.
      -Your graphics card
      -YOU NEED an imac 2011 gpu heatsink
      -GOOD thermal paste (Preferably liquid metal if youre comfortable with that)
      -IMAC 2010 power supply
      *As far as i know the power supply's between these 3 imac's are interchangeable, but the largest one is the 2010 variant, at the 310 watts, and the others are much lower.
      *Just from tdp we know that the 980m is 115w and the cpu's on these guys are most commonly 95w, thats allready 200 with out hdd, all the other components etc.
      -nvidia web drivers
       
      READ THE FOLLOWING DIRECTIONS CAREFULLY
       
      Step 1: You must have all your mac os/ windows partitions set up with bootcamp, and MAKE SURE it boots into Mac OS and wont boot into anything else when you start it up AFTER the upgrade.
      *Remember nvidia web drivers must be installed before you upgrae
      Step 2: dremel/ cnc/ remove a couple parts of the VRM section of the imac 2011 heatsink, (You want your card IN HAND so you are able to make sure it fits correctly.
      step 3: Assemble the gpu assembly
      step 4: Re assemble the imac, with the new gpu.
      *This is where is gets slightly harder*
      step 5: You want to reset your iMac's System Management Controller, otherwise known as SMC.
      *DO NOT FLASH NVRAM OR PRAM, or you will have to redo the whole process, after you put your old gpu in to fix all the bootcamp problems and such
      *You can do this by plugging the power cord into your imac, waiting 30 seconds and NOT turning it on, unplug your power cord, wait 30 seconds, then plug it back in. Wait another 30 seconds, then turn it on. (But not before reading the following to be prepared:)
      step 6: You need to force Mac OS to work with an unsupported card. this is a pretty simple process if you are comfortable with terminal.
      * I couldn't have found this without this page: 
      https://www.ifixit.com/Story/18646/Successful_iMac_Upgrade_to_GTX_880M
      "
      To make a non-apple provided Nvidia graphics card work in macOS Sierra you need to do the following…
      Start the computer in safe mode by holding shift.
      Get your BoardID by running this command in terminal
      echo "<result>$(ioreg -rd1 -c IOPlatformExpertDevice | awk -F'["|"]' '/board-id/{print $4}')</result>"
      Open the AppleGraphicsControl Kext using this command
      sudo nano /System/Library/Extensions/AppleGraphicsControl.kext/Contents/PlugIns/AppleGraphicsDevicePolicy.kext/Contents/Info.plist
      Use the arrow keys to go down until you see <key>ConfigMap</key> followed by a bunch of keys and strings.
      LOOK FOR YOUR BOARD ID…
      IF IT IS LISTED: Change the string to <string>none</string>
      IF IT IS NOT LISTED: Add it in the same format as the ones listed.
      Save the file by pressing Ctrl+O, then enter.
      Exit by pressing Ctrl+X
      Rebuild the kernel cache using the following two commands:
      sudo kextcache -system-prelinked-kernel
      AND
      sudo kextcache -system-caches
      Have Fun!
       
      Theoretically this should work, and I would love for somebody to try as I got an 880m instead. Just keep in mind this is all from research and has not been proven to work. Be sure to research this subject before you try it.
    • By shogun
      Fellow Users, I kindly ask every owner of Clevo P170SM to share their experience with updating their system with Prema BIOS P170SM_34_31_PM_v2.
       
      FAQ
       
      Q: What is the checksum of the official "P170SM_34_31_PM_v2.rar"?
      A: MD5 checksum is: 07198c20968275d6004562d4e5da89ef
       
      Q: What is the password to "P170SM_34_31_PM_v2.rar"?
      A: The password is: premamod.com
    • By mrsmile1015
      Just recently puchased a Clevo Gtx 780m on ebay and inserted it into my Alienware m17x r4. I'm terrible dissapointed to find the BIOS a12 unlocked and device mananger doesn't detect it at all. Are there some steps I have to undergo to make it work? 
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.