To anyone wondering about eGPUs on M6700s, its not too complicated, there is just a process that must be done on boot every time:
You need to have the eGPU connected and powered on before booting the laptop, once you get to the Intel RAID screen disconnect the eGPU and wait for windows to load up, once windows is loaded reconnect the eGPU and you *should* be able to use it and be able to hot-swap it (though you should disable it in windows before unplugging it) installing the normal AMD drivers worked fine for me, though the original release of Adrenaline 19.1 blue screened the first time.
I usually run with 3 1080p monitors attached to the 480, replaced my old i5 desktop with this laptop due to the convenience of storing everything on one machine, the laptop has a 256gb SSD and 2x 750GB hdds in raid 0, there is a 2TB WD black attached to the eSATA on the dock.
eGPU and external HDD are powered by a 500W evga desktop ATX psu, the EXP GDC's ATX power adapter was clunky and broke while trying to use it, so I just plugged in a CPU 4 pin cable upside down to power it, not worried about it because the bulk of power is coming from the 8 pin on the GPU anyway.
Hello Fellow Tech Gurus!
I am having a huge headache after upgrading the ram memory of my m17x r3.
First let me start by saying I have been experiencing issues with my current ram setup recently, and so i decided to replace the ram inside of my computer, thinking they had gone out on me. It originally came with x4 2gb memory sticks, and as I started to experience issue, I started to removed them, and I was down to 1 2gb stick. It seems to me ram slots 1 & 2 are not working properly as when I put ram memory into them I would get BSOD in 5-10 mins of computer usage after boot. So I am thinking the slots have gone out. I also tested each slot individually and still same effect.
So I went on the try out slots 3 & 4 under the keyboard, which seems to work just fine when I use only 1 ram chip in one or the other. But the problem occurs when I try and fill both ram slots in slots 3 & 4 under the keyboard with crucial 2x 8 gb of ram sticks, which total to 16gb total ram memory.
BSOD and freezing occurs like crazy. But if I use just one of the ram sticks in either slot, no problem.
I dunno if this is hardware or software. I am think that my motherboard is on its way out the door, but any suggestions you all have would be great. I have already clean installed win 7, and is currently running bios A10 (unlocked, I believe)
I would also like to note that my motherboards internal vga is not detected, and just noticed this a few days ago upon trying to figure out the ram situation.
other issues is my laptop battery is pretty much dead, and the only for my computer to cut on is if the AC adapter is connected
I would also like to know can 1x 16gb 1600 ram stick run in my computer? or is it not supported by my motherboard?
Alienware M17xR3 (2011 3D FHD ed)
A10 (should be unlocked)
Microsoft Windows 7 Home Premium (64-bit)
Intel® Core™ i7-2960XM CPU @ 2.70GHz
Intel® 6 Series/C200 Series Chipset Family
Nvidia GTX 680m
IDT High Definition Audio CODEC
High Definition Audio Device
Networking and I/O
DW1501 Wireless-N WLAN Half-Mini Card
Atheros AR8151 PCI-E Gigabit Ethernet Controller (NDIS 6.20)
HMA TAP-Windows Adapter V9
Crucial 8 GB (x2 qty) DDR3 PC3-12800 • CL=11 • Unbuffered • NON-ECC • DDR3-1600 • 1.35V • 1024Meg x 64 •
(these only work under bay 3 or 4, but not dual 8gb at the same time, otherwise BSOD)
WDC WDBNCE5000PNC SSD (installed into bay 0)
I just got a Dell r9 m290x card for my m17x r3. I'm using the stock A12 BIOS. Had PEG set in the BIOS and on boot had a black screen. I cleared CMOS, most likely reverted back to SG and on boot had a black screen with 8 beeps.
I've seen people on here report that it is working for them. Do I need to use a different vBIOS? Or maybe the unlocked A12 BIOS with some settings changed?
Any help would be appreciated Thanks.
I use Dell M6700, 2GB K3000M graphics card.
I see the overclock is hopeless.
Computer M6700, Windows 10.
I installed the Msi afterburner, but could not unlock the voltage.
I flash vbios as per instructions:
I open the CMD to the desktop (the folder containing rom and nvflash)
K3000m rom i downloaded here:
I heard a beep when using the nvflash --protectoff command
and another beep when using nvflash k3000m.rom
However after doing all that. I installed the afterburner msi, everything is the same. I have edited the MSG afterburder CFG file by making changes like:
Format = 2
VDDC_Generic_Detection = 1
All have no effect.
I want to upgrade my GPU ( K3000M to other card ) from M6700
I found it :