Jump to content
EwinRacing Flash Series Gaming Chairs
Brian

[BENCHMARKS] The OFFICIAL Thread

Recommended Posts

15 minutes ago, Khenglish said:

@johnksss

 

Amazing memory clocks. What voltage? Just the 1.48V?

Thanks.

 

Yeah, but not sure if the pencil helped any because at first I couldn't figure out why it wasn't working, but I think that has since wore off. So it would be based off your hard mod. And if that is 1.48V, then that's what is running....I think. lol

Edited by johnksss

Share this post


Link to post
Share on other sites
4 hours ago, Khenglish said:

 

Do you actually get a performance benefit for vBIOS over 1.2V? I always got best performance on a 1.2V vBIOS. The extra clocks from over 1.2V did not compensate for the bizarre throttling that occurs and increases as you pass 1.1V. The 980m also compensates for vDroop very poorly, adding too much voltage at lower voltage vBIOS, and too little for higher voltage vBIOS (with the 1.225V or 1.25V vBIOS being the most correct). This is why the 1.2V vBIOS draws more power than the 1.25V vBIOS you were using, despite the higher nominal voltage and clocks when running 1.25V.

 

The M5500 vBIOS base that Prema gave me seems to have the incorrect vDroop issue fixed, but I think I am still getting the ~2% throttle than is seen on the 1.2V vBIOS.

 

And I realized that I mixed up which card is which. So the card I am using now did 1475MHz memory prior to any mods , and the one you are using now did 1450MHz memory? Sorry for all the questions, I'm just trying to figure out why I currently struggle to get just 7GHz.

Yes, absolutely... much better. In fact, my core overclock is limited by the 1.2500V firmware I have now. I will see if I can get @Prema to goose it to 1.300V for core voltage once I have a matching GPU for SLI. I can just barely do 1510 on core with 1.2500V right now. About half the time that TDRs due to lack of voltage and anything above 1510 gets flashing and severe artifacts from lack of core voltage. But, 1500 is rock solid stable with 1.2500V. Part of the problem is high ASIC score. It seems the higher the ASIC score is the more core voltage is required for the same overclock. Adding the three missing MOSFETs also seems to increase the amount of voltage needed for the core overclock.

 

I don't have any throttling at all with high voltage, but I am using AC cooling like @johnksss so that may have something to do with that. Even with those extreme overclocks the GPU generally stays below 50°C, and most of the time under 35°C under full load.

  • Thumbs Up 1

Share this post


Link to post
Share on other sites
2 hours ago, johnksss said:

Thanks.

 

Yeah, but not sure if the pencil helped any because at first I couldn't figure out why it wasn't working, but I think that has since wore off. So it would be based off your hard mod. And if that is 1.48V, then that's what is running....I think. lol

 

You might want to check the voltage. You can easily be running 1.7V+ and burn out the memory.

Share this post


Link to post
Share on other sites

Pretty warm, but was able to game at 1536/3600 or 7.2 ghz. Single card

Edit: Fallout 4. 

Fallout4op_2016_07_31_21_14_01_583.jpg

Fallout4op_2016_07_31_21_20_59_276.jpg

Fallout4op_2016_07_31_21_27_24_294.jpg

Edited by johnksss
  • Thumbs Up 2

Share this post


Link to post
Share on other sites
3 hours ago, johnksss said:

Pretty warm, but was able to game at 1536/3600 or 7.2 ghz. Single card

Fallout4op_2016_07_31_21_14_01_583.jpg

Fallout4op_2016_07_31_21_20_59_276.jpg

Fallout4op_2016_07_31_21_27_24_294.jpg

What game is that? I don't recognize the environment. Fallout 4?

Share this post


Link to post
Share on other sites
16 hours ago, Khenglish said:

 

You might want to check the voltage. You can easily be running 1.7V+ and burn out the memory.

1.43V is the calculation I get.

Edited by johnksss

Share this post


Link to post
Share on other sites
47 minutes ago, johnksss said:

1.43V is the calculation I get.

 

You said you pencil modded too. Pencils mods actually bake in over time and lower resistance even more than what you initially read after the mod.

Share this post


Link to post
Share on other sites
8 hours ago, Khenglish said:

 

You said you pencil modded too. Pencils mods actually bake in over time and lower resistance even more than what you initially read after the mod.

For a day. It didn't work as intended so I just wiped it off. Checked resistance and it's exactly where it started. 11.9 while installed.

Edited by johnksss

Share this post


Link to post
Share on other sites

27/33k how awesome is that! 1800Mhz vRAM, that's insane! :D

  • Thumbs Up 2

Share this post


Link to post
Share on other sites

Dear @johnksss

Within the next few days I'll get a Clevo P570WM with i7 4930K, 16GB, GTX 880m SLI, 256GB SSD + 1TB SSD Raid,  2X330W PSU, how much do you think I can get from it after flashing @Prema bios and flashing the vBios as well?.

Maybe @Mr. Fox can help as well, he is one of our heros :super:

Edited by Dr. AMK
  • Thumbs Up 1

Share this post


Link to post
Share on other sites

BTW, the RAM speed is it important? I saw many videos and benchmarking between the 1333, 1866, 2400 and not that much different. Do you think I need to change my 1600 one?

Share this post


Link to post
Share on other sites

Here is the highest recorded 880M SLI score for 3DMark 11 on a laptop with a quad core... It is not many points behind the highest score recorded by a P570WM with 4930K CPU.

http://www.3dmark.com/3dm11/11477144

[IMG]

 

Here's a new 880M SLI world record for Fire Strike. Once 3DMark adds the hardware ID (requested) the score will be validated with the GPUs recognized.

http://www.3dmark.com/fs/9676618

[IMG]

  • Thumbs Up 3

Share this post


Link to post
Share on other sites

Thanks @Mr. Fox 

The different between the 880'sM and the 980'sM almost 10,000 wow, really a big different. Hope that the P570WM can support the GTX 1080 so I can upgrade in the near future.

Edited by Dr. AMK
  • Thumbs Up 1

Share this post


Link to post
Share on other sites
3 hours ago, johnksss said:

Thanks goes to @Khenglish!

vzQOJ5q.jpg

 

What are you getting for max stable memory clocks? For the MSI with the 7ghz chips I could bench at 7.5ghz or 7.6ghz, but for fully stable I needed to drop all the way down to the low 6.9ghz range. When playing with other cards they did not have such a big difference netween benchable and fully stable.

 

Also is that 5ghz on the cpu?

 

A little update, the 980(m?) now has 5 of the 980's memory chips installed. Memory clocks are improving.

Edited by Khenglish
  • Thumbs Up 2

Share this post


Link to post
Share on other sites

I posted gaming benchmarks a few post earlier. I was playing at Fallout 4 @1.536ghz / 1.8ghz overclock on 6ghz rated memory.

It seems to be somewhat less under windows 7 though. 1.5ghz / 1.753ghz.

 

I wish, but nope. It's about 4.5 ghz on cpu.

 

Did you try the 368.89 drivers yet? I would start there....

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

OK, just took first place on Fire Strike, 3DMark 11 and Vantage for 880M SLI... These comparisons are against current first place scores. Once 3DMark adds my hardware ID these will show in search results and displace the guys currently in the #1 spot to the #2 and #3 spots based on what I have uploaded today.

 

http://www.3dmark.com/compare/fs/2402025/fs/9686855

 

http://www.3dmark.com/compare/3dm11/8510683/3dm11/11477498

 

http://www.3dmark.com/compare/3dmv/5067708/3dmv/5494902

 

pkUVOgE.jpg

DFSVR84.jpg

12zBxd8.jpg

 

 

  • Thumbs Up 3

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By BAKED
      BAKED BIOS FOR TM, KM, DM, P6, P4 SERIES WITH MOST MENUS AND OPTIONS UNLOCKED PLUS OTHER MODIFICATIONS
       
      NEW:
      I HAVEN'T BEEN ACTIVE IN A WHILE BUT I MIGHT FIND SOME TIME SOON TO WORK ON AND RELEASE NEW MODS.
      I STARTED WORKING ON V3.0 A WHILE BACK WHICH WILL INCLUDE UPDATED UEFI DRIVERS, MICROCODE, BIOS SCREEN SHOT SUPPORT AMISCE SUPPORT(For some models) PLUS MORE. 
      ALL TM, KM AND DM SERIES ARE V2.0 AND NOW HAVE WINDOWS FLASHER INSTEAD, JUST EXTRACT AND RUN FLASH.BAT
      WARNING! BIOS FLASHING IS RISKY SO MAKE SURE YOU KNOW WHAT YOU'RE DOING BEFORE PROCEEDING. 
      FLASHING THE WRONG BIOS OR INTERRUPTING THE FLASHING PROCESS WILL BRICK YOUR SYSTEM! 
      USE AT YOUR OWN RISK!
      TM, KM AND DM SERIES
      P6 AND P4 SERIES
      INSTRUCTIONS
       
    • By qamar198
      Hello Everyone,

      I am trying my Sager NP 9377 to get to work but to no avail. NO POST, NO DISPLAY.
      in short>> powering on laptop causes fans to run at full speed after 10(cpu only) + 10 (now both cpu+gpu) with Caps Lock + Num Lock + Scroll Lock LEDs blinking, continuous 1 second beep, repeats for one minute with 1 second in between, then laptop shuts down.

      IN DETAIL
      System Specs are i7 4810mq 8gb gtx 880m SLI variant (though my laptop has other GPU Slot empty so only singular 880m running) 120 Hz display.

      The Problem
      > if i take out the battery and plug in AC only, the power light comes on ORANGE
      if both battery is connected, then i have both power and battery light ORANGE
      and if only battery is connected then of course laptop is waiting for me to press the power button
      but in all 3 cases the following happens
      > Pressing the power button brings laptop to some signs of life, power LED turns green, both the CPU and GPU fans have a very quick jerk but does not spin., keyboard lights up with Blue Backlight (dont know if this is relevant or not), HDD activity light starts to blink showing HDD access maybe (even when hdd is removed)
      > Display remains blank (i dont even sense the display backlight being on)
      > HDD activity light sometimes goes off after only 1-2 seconds, sometimes shows rapid blinking/activity for 4-5 seconds
      > both fans remain off (i removed back cover to check this)
      > after about 10 seconds or so, the CPU fan spins up (speed is normal, just like when using the laptop in IDLE)
      > after 10 more seconds have passed, the CPU fan seems to be turning off for a split second then both the CPU and GPU fan turn on full speed with a lot of noise.
      > Caps Lock, Num Lock and Scroll Lock LEDs all blink together with single beep for about 1 second, repeats beep with 1 second in between.
      > goes on for about 1 minute then laptop shuts down.
      > forcing the fans to spin down using FN+1 key makes them spin back up to full speed after a split second (dont even know why i tried this one -_-)

      What I Have Tried So Far
      > EC and Bios Reset (take out battery, disconnect AC Adapter, disconnect CMOS Battery, Press Power Button for upto 30 seconds)
      > Change Ram and check all available slots
      change/remove HDD
      > Repaste CPU/GPU and clean out fans
      > Checked GPU...... Flashed the 880m in this Sager with MSI vBios and tested it in a MSI Gt70 2PC i have, gpu ran fine, tested with FurMark, AC Odessey, Ghost Recon Wildlands for over an hour (unfortunately the cooling in my MSI is not good enough it already runs hot, and this 880m causes thermal throttling as well as power limit throttling sometimes). Reflash 880m with original Clevo vBios and put back into the Sager, still no boot, same results as before.
      > Checked the CPU..........checked the 4810mq in the MSI GT 70 which worked fine, as well as tried the 4810mq from the MSI in the Sager, still no boot.
      > Suspected bad GPU fan connection......therefore forced both fans to full speed as soon as i press power button (using FN+1 Keys) and both fans turn on full speed, same results.
      > tried charging the battery to the max before turning on on battery only, same results.

      >>------- The laptop has had some random shutdowns in the past too during gaming but would turn back on fine after waiting for 10 mins or so, then i sold it to some guy who brought it back to me the next day saying that it just turned off during gaming and wont turn back on, i returned his money, did all the troubleshooting above to no avail. then i finally put it aside to wait until i get some other system in which i can test the CPU and GPU.
      Then one day i turned it on (after leaving it untouched for a couple months), same results as above, i decided to try once without battery and it Freakin Turned ON!!!, used it for a couple days without battery, played a few games (thermal throttling was observed here and there), but then this happened again and this time it seems permanent . And now i have not only repeated all the steps above but this time also checked the CPU and GPU in the MSI GT70 too. ------------<<


      Some Observations
      > touching the CPU heat pipes feels warm, but the GPU heat pipes are colder (GPU never even booted?). dont know if this is normal or not.
      > i replaced one of the capacitors near the CPU once, but i did use the laptop for quite a while after that without any issues.
      > my Idle temps were always below 40c for both CPU and GPU, so an overheat warning as soon as laptop is powered on seems unlikely (false overheat warning?, but GPU does not even seem to be detected/ booted as heat pipes remain cold to touch), also i repasted the CPU and GPU multiple times.
      > The guy who sold me the laptop told me that the power adapter was originally a Dell, and it was modified to use with this Sager by replacing the cable with a 4-Pin one from a Toshiba (same pinout as the Sager), but then again i have used this laptop for quite a while on the same adapter.
      > From day 1 of having this laptop, some keys on the keyboard (w, s, t, c and numpad 4) did not work 99% of the time. pressing really hard on any one of them sometimes made ALL of them work for a while. any thoughts on this issue?? (even if its unrelated).

      So what seems to be the issue here?
      GPU not detected ?, False temperature alert?, Bad fan?.
      Any help towards resolving this will be greatly appreciated.
      Thanks in advance .
    • By BasedKnight
      I recently purchased a replacement 980M (Clevo model) for my P770DM-G after the original died, however, after installing the card the laptop doesn't boot. I only get a black screen, and after a couple minutes the fans spin to max before shutting down, which is the same thing that happens when I try to boot it without any gpu at all. I've tried the reset procedure, unplugging, removing battery, and removing CMOS, to no avail. It does beep before shutting down (I counted 22 times exactly). Anyone have any insight as to what the problem is?
    • By Kunal Shrivastava
      Hi guys, I am the proud owner of a Clevo p775dm3-g notebook purchased from azom.systems (authorized Clevo reseller in India, Model rebranded as Azom Legion-17.3 inches). Here are my specs:

      Core i7 7700 (non-K version): undervolted by 110 mv and turbo boost disabled in BIOS- machine uses prema mod BIOS.
      GTX 1080: undervolted by 100 mv on all frequency steps using MSI afterburner voltage/frequency curve editor. clocks are untouched.
      16 GB DDR4: Cant remember clocks.
      1440p 120 Hz screen: No tinkering done to refresh rate.

      CPU has been delidded and repaste has been done on both CPU/GPU dies with gallium based TIM-Coolaboratory liquid ultra if I recall correctly.

      My issue is GPU hitting max temp limit of 90 degrees while playing DOOM and framerate drops from 110 avg to mid 60s-70s with horrible stuttering- this is thermal throttling for sure.

      System was running beautifully after repaste at 86 degrees max/ 77 degrees average at 100 percent fan speed. A month later I decided to see how much further I could push the system and ended up undervolting the CPU/GPU and RAM even further. The RAM undervolting part didnt work as well as I'd hoped, and I ended up resetting the BIOS to undo everything and reapply the previous setting (-110 for CPU with turbo boost disabled.) 

      I noticed that immediately after BIOS reset, both my CPU and GPU temps were 5-10 degrees higher even with the undervolt/underclock applied. Also, I think the fans were a bit louder before I reset the BIOS which leads me to believe that for some reason the fans are now capped at 80% max fan speed. There doesnt seem to be a fan speed selector in the BIOS or anywhere else so I cant say for sure whether this is a fan related issue or something else.Before the reset I could override the BIOS setting and set the fans to 100% by pressing fn+1, could I have done something to that setting after resetting the BIOS ? I dont think I have damaged the CPU or GPU as temps are holding fairly steady at 90-91 degrees and laptop doesn't shut down while gaming.

      If I have overlooked something or if anyone reading this has any solution help would be greatly appreciated.
      All settings/drivers/windows version/app version are exactly the same before and after BIOS reset.
    • By racerxdl
      Hi all,
       
      It has been a while since I did anything to my laptop (Clevo P670RG-G) and since I recently got a VR Headset I wish I could overclock my GPU a little. So far the NVidia software (on windows) doesn't allow me to overclock it (the linux sort of allows, which some custom Xorg options) so I decided to give a try modding the vbios.
       
      I read all sorts of issues / guides about it, and it seens that the hardware topology (where the vbios is stored and how things are connected) changes from machine to machine.
       
      What I know about my laptop is that it has two VBios, one for Hybrid Mode and one for Discrete Mode. I'm currently running the discrete mode.
       
      I dumped my VBios using GPU-z and opened up in Maxwell II Bios Tweaker. Everything seens fine so far.
       
      So I have few questions about it:
       
      - There is a way to just unlock the VBios to show the overclocking options in NVidia software? (That way I dont need to reflash to change clocks)
      - I can just flash this GPU-z dump to my VBios?
      - If I brick my GPU, that GPU-z dumped image is the raw SPI image, so if I managed to physically access the VBios, I can just reflash over it?
      - I saw some people saying that I might need as well to flash the main laptop bios as well, is that really needed?
       
      Thanks!
       
      Lucas

×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.