Jump to content
Brian

[BENCHMARKS] The OFFICIAL Thread

Recommended Posts

The official Clevo benchmark thread..let the race begin!

 

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

Below no longer relevant after launch of T|I 2.0

 

So... let's see what Clevo/Sager laptops can do 

How to submit your scores

1. Make a post in this thread that will contain a screenshot, provide a link of your results if it is a 3DMark Vantage/11/06 run and post anything else you feel like mentioning for that particular run, i.e ambient temperatures, cooling method, etc...

2. Go to Forms and locate your laptop and then click on the benchmark you want to submit your results

3. Complete the form. The last question of the form will ask you to submit the link of either your post or the link of the screenshot you took (i.e [ URL]www.example.com/1.jpg )

Note: You must type those tags (don't copy-paste them from this post, must be in capital letters, no spaces,) like the example above in order for the link to be clickable.

In case you want to edit or delete your submission or need assistance on how to submit your score check the guide here

************************************************** **************************************************

Clevo/Sager League

3DMark Vantage

3DMark 11

3DMark 06

 

 

Share this post


Link to post
Share on other sites

Share this post


Link to post
Share on other sites

I'm sorry I did not notice your answer before.

My P150HM stock cooling system works well. It's full stable now up to 1100/2700MHz/1.05V for GPU and 2x4.4GHz for CPU.

gtx680m11002750mhz.jpg

No Fn+1

The K5KM results were with untouched card.

There is no Optimus/Enduro on P150/170HM.

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

Hey guys, here is my benchmarks with stock gpu clocks. I haven't tweaked my system yet but will keep you posted when I do !

But first my spec is :

  • Chassis & Display : Clevo P150SM Matte Full HD LED Widescreen (1920x1080)
  • Processor (CPU) : Intel® Core™i7 Quad Core Mobile Processor i7-4800MQ (2.70GHz) 6MB
  • Memory (RAM) : 8GB KINGSTON HYPER-X GENESIS 1600MHz SODIMM DDR3 (2 x 4GB)
  • Graphics Card : NVIDIA® GeForce® GTX 780M - 4.0GB DDR5 Video RAM - DirectX® 11
  • 1st Hard Disk : 120GB KINGSTON HYPERX 3K SSD, SATA 6 Gb/s (upto 555MB/sR | 510MB/sW)
  • 2nd Hard Disk : 500GB WD SCORPIO BLACK WD5000BPKT, SATA 3 Gb/s, 16MB CACHE (7200 rpm)
  • Thermal Paste : ARCTIC MX-4 EXTREME THERMAL CONDUCTIVITY COMPOUND (£9)
  • Sound Card : Intel 2 Channel High Definition Audio + MIC/Headphone Jack
  • Network Facilities : GIGABIT LAN & KILLER™ 1202 WIRELESS GAMING 802.11N + BLUETOOTH 4.0

3DMark11 : NVIDIA GeForce GTX 780M video card benchmark result - Intel® Core i7-4800MQ CPU @ 2.70GHz,Notebook P15SM

3DMark 2013 Firestrike : NVIDIA GeForce GTX 780M video card benchmark result - Intel® Core i7-4800MQ CPU @ 2.70GHz,Notebook P15SM

Also did a Windows performance yesterday and really good result :

post-15857-14494995882385_thumb.png

  • Thumbs Up 2

Share this post


Link to post
Share on other sites
Here's an Alienware for you clevorr NVIDIA GeForce GTX 780M video card benchmark result - Intel Core i7-3940XM,Alienware M18xR2

Well I guess I have an advantage with 780M but your physics score sure is great.

Yeah can't really compare 680 with 780, its like chalk n cheese. If my machine had 780,s it would be another broken record but i couldn't be bothered and my 680,s work very well. Very Nice AW Score there though!! I think i am gonna wait for whatever is after the 780m then upgrade..

  • Thumbs Up 1

Share this post


Link to post
Share on other sites
4X4 Actual

Oh I see now how futuremark is saying you have 16GB with only 2 4GB sticks now.

Share this post


Link to post
Share on other sites

Im getting a p157sm next week :Banane44:

i7 4700mq

16GB Ram

GTX 780m

250GB SSd

As soon as i have it, i will post some benchmarks.

If Prema´s bios mod would be ready i:83: could test some OC too.

  • Thumbs Up 1

Share this post


Link to post
Share on other sites

Is there a recent CPU/GPU overclocking guide for Clevo/Sager laptops? While I have experimented with Intel XTU have gotten a 12.5k 3DMark 2011 bench with 780m SLI stock, seeing 680m SLI hitting 15k+ Custom XTU settings? Custom GPU settings? Voltage mods? Power supply upgrades?

Just wondering what a best practice is for someone who wants to try his hand on overclocking a gaming laptop. I see people posting benchmarks, but casual searching I see posts like this - http://forum.techinferno.com/general-notebook-discussions/4372-780m-gtx-overclocking-2.html , but again the results are being discussed but not the steps on how to get there in a FAQ or Step by Step form. I am curious to try and find an overclock setting for the GPU's and CPU that will work with my Sager 9380-S with a default 330w brick.

Kind Regards,

Koinonos

Share this post


Link to post
Share on other sites

Hi guys somebody help me out.... I have a W230ST core i7 4700MQ with 8GB of ram. I have overclocked the machine with nvidia inspector with the following settings.

+135mhz on the core clocks and +400mhz on the memory clock. It won't go more than that as 3D MARK 2011 crashes. :( I am getting a score of 4778 but some people are getting a lot more than that. What to do? I am using a Thermaltake cooling pad which does a good job with the temps (lowering CPU up to 5 degrees centigrade - not bad for a €20 cooler).

Any suggestions on how to improve my 3D MARK score? Should I overvolt the GPU a bit in order to balance the high clocks? I don't know what to do. I appreciate an answer from the forum.

Share this post


Link to post
Share on other sites

@gnikolaides that depends, you need to figure out the reason behind 3DMark crashings. Is it due to high temps or due to lack of voltage with the higher clocks? If it's due to high temps overvolt won't help cause you need to keep temp low, otherwise overvolting will solve your problem. Also consider ambient temperature (if it's too high that won't help) also running the bench consecutive times won't improve your score cause the heatsinks are getting hot and they don't have enough time to cool down, plus some people when benchmarking tend to use a portable A/C unit blowing cold air directly to the heatsinks and helps them keep temps even lower therefore having extra headroom for higher clocks or voltage.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By BAKED
      CHECKING TO SEE WHICH CLEVO MODELS YOU WOULD LIKE ME TO MAKE BIOS MODS FOR.

    • By ElChuterRD
      Greetings, I have a p650rs and I have this little problem that I can not play in MRHYBRID mode, only if the charger is connected, and I do not see high quality videos or play if it is in discret mode, if the A / C is connected.
       
      Any idea what it could be?
       
      I have the latest version of Bios and ECF
      I've been looking for custom-made Vbios but I can not find anything.
      Thank you


    • By DR650SE
      Hey guys! Long time no see! Been ages since I've been here and wow has this place changed! @Briankeep up the great work!  I've been pulled away from my computer passion by raising 3 kids! All 6 and under.  Crazy how time flies! 
       
      On to what brings me here.  Love you oming for some ideas.
       
      My X7200 was recently shutting down randomly. The num lock and caps lock would start flashing and then it'd shut down. CPU and GPU Temps looked good, but fans were running a lot.  I figured whatever was hot was something HW Info couldn't see or read.  
       
       
      I repasted my GPUs and CPU, put in new thermal pads as well. Unfortunately when I tightened the CPU heatsink, I must have over tightened a screw because it pulled the screw sleeve on the mobo out. Temps are still good, idle around 33°C, and fans run full bore all the time. So it may not have quite enough pressure on a mofset or something. On the plus side, I let the computer sit on for 16-18 hours idle,and it didn't shut down, which solved one issue and created another.

      Would I be okay to superglue it back down to the mobo? Should I use some other adhesive? Then it would create a tad more pressure, evenly, and possibly solve my fan issue. Damn these old computers. Purchasing a newmobo would probably be more expensive than it's worth.
       
      I really need to retire this thing, but it's served me faithfully since Oct 2012. Eventually I'll move to something more mobile and a desktop. 
    • By dimaginexus
      It's locked & hidden by default, but I've got an i7 8700k & I'd like to use the intel graphic on my hackintosh mojave.
      Is there any way to activate or mod this?
      Thanks!
    • By BAKED
      BAKED BIOS FOR TM, KM, DM, P6, P4 SERIES with most menus and options unlocked. 
      These BIOS mods are only for advanced users who know what they are doing.
       
      NEW: New versions on all KM and DM series plus new mods for P7XXTM1 and P870TM1
      Mods for more models will be rolling out soon.
       
      WARNING! BIOS FLASHING IS RISKY SO MAKE SURE YOU KNOW WHAT YOU'RE DOING BEFORE PROCEEDING. 
      FLASHING THE WRONG BIOS OR INTERRUPTING THE FLASHING PROCESS WILL BRICK YOUR SYSTEM! 
      USE AT YOUR OWN RISK!
       
      TM, KM AND DM SERIES
       
      P6 AND P4 SERIES
       
      INSTRUCTIONS
        IF YOU LIKE MY WORK BUY ME A COFFEE =>DONATE<= ENJOY!
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.