Jump to content
Apologies for the spam Read more... ×
Prema

[BIOS/vBIOS - MODS] Prema Mod™ & Stock

Recommended Posts

I have "MSI GT72" with "970M 3go" and I would like replace by "980M 8go CLEVO", I need vbios MSI for "980M CLEVEO", thank.

 

 

Share this post


Link to post
Share on other sites
4 hours ago, reneyvane said:

I have "MSI GT72" with "970M 3go" and I would like replace by "980M 8go CLEVO", I need vbios MSI for "980M CLEVEO", thank.

 

 

What the vbios version in your "980M 8go CLEVO" card?

Share this post


Link to post
Share on other sites

Hello,

Actually this is my card that I am selling. So it's a prema-biosmodded card that I have bought from eurocom.

Does it fit mechnically in a GT72 and will it work? If do you know if it requires a bios update of the GT72?

Edited by greg_p

Share this post


Link to post
Share on other sites
16 minutes ago, greg_p said:

Does it fit mechnically in a GT72 and will it work?

Mechnically? Yes of course.

 

26 minutes ago, greg_p said:

If do you know if it requires a bios update of the GT72?

If you mean main system bios, then i think it's not necessarily, but it's good idea.

If you mean vbios, then yes, the best choice to flash MSI vbios.

Share this post


Link to post
Share on other sites

you mean an official or a prema? As it's not an card initially done by/for msi, there could be some differences with original. Or may be the mxm standard doesn't really leave place for that kind of difference and it doesn't really make a difference.

So it si compatible? good news! I am looking for vbios so.

Share this post


Link to post
Share on other sites

I have a  Clevo P651SE but does not recognize from DOS or BIOS my new NVMe SSD 960 EVO Samsung... so I cannot boot from that disk. If I boot from windows the disk is visible through windows as secondary.... what I must do to fix this... Bios Update or just some adjustments?

Share this post


Link to post
Share on other sites
17 hours ago, Treleo said:

I have a  Clevo P651SE but does not recognize from DOS or BIOS my new NVMe SSD 960 EVO Samsung... so I cannot boot from that disk. If I boot from windows the disk is visible through windows as secondary.... what I must do to fix this... Bios Update or just some adjustments?

I had this issue

 

I know it sounds stupid and shouldn't work, but boot from a linux live CD and format your drive as NTFS. the windows installer should see it once it's been formatted once.

Edited by SrzCase

Share this post


Link to post
Share on other sites

windows installer (f it is windows 10) can see it normally ... You can also intall windows and make all partitions ect... But when is trying to reboot and bios trying to find drives to boot from... cannot see the M2 NVMe disk but only the installer disk or usb drive. So it starts installation from beginning...

So the problem is to be able to see it from BIOS and not only from windows installation disk/drive. 

Share this post


Link to post
Share on other sites

Hello

I have a Clevo 157SM.

Whenever the processor reaches a certain temperature the fans start to run at maximum speed and even if the temperature goes down they only shut down after a long long time.

Is there any new version of BIOS?

Is there any option where I can change the temperatures?

 

My Bios Info:

ME FW Version - 9.0.31.1487

MB Series - P15SM
Bios Version - 1.03.04CC v2
KBC/EC Firmware Revision - 1.03.01

 

 

Thanks in advance

Share this post


Link to post
Share on other sites
On 17.05.2017 at 1:00 AM, Treleo said:

I have a  Clevo P651SE but does not recognize from DOS or BIOS my new NVMe SSD 960 EVO Samsung... so I cannot boot from that disk. If I boot from windows the disk is visible through windows as secondary.... what I must do to fix this... Bios Update or just some adjustments?

1 - Make sure you unplug all SATA and USB drives, the M.2 drive has to be the only drive installed.

2 - Go into the bios, under the boot tab there is an option for CSM, make sure it is disabled.

3 - Click on secure boot option below and make sure it is set to other OS, Not windows UEFI.

4 - Click on key management and clear secure boot keys.

5 - Insert a USB memory stick with a UEFI bootable iso of Windows 10 on it, USB3 is quicker but USB2 works also. A Windows DVD won’t work unless you’ve created your own UEFI Bootable DVD.

6 - Press F10 to save, exit and reboot.

7 - Windows will now start installing to your NVME drive as it has its own NVME driver built in, I don't think this would work with previous versions.

8 - When the PC reboots hit F2 to go back into the BIOS, you will see under boot priority that windows boot manager now lists your NVME drive.

9 - Click on secure boot again but now set it to WIndows UEFI mode.

10 - Click on key management and install default secure boot keys

11 - Press F10 to save and exit and windows will finish the install.

Once you have Windows up and running, shutdown the PC and reconnect your other SATA drives. Do not put anything on SATA port 1 as this is now reserved for the NVME drive.

I would also recommend installing the Samsung NVME driver at this point to replace the Windows one.

The background here is NVME SSDs do not appear within the BIOS until Windows creates the system partition with the EFI Boot Sector.

Your M.2 SSD contains UEFI driver information within the firmware. By disabling the CSM module Windows will read and utilize the M.2-specific UEFI driver.
 

 

 

If this does not work, make a bootable usb with this ISO http://www.samsung.com/semiconductor/minisite/ssd/download/tools.html

Boot from it, instal the firmware and after that windows installer will see you drive.

Edited by runix18

Share this post


Link to post
Share on other sites

Windows installer CAN SEE my drive... BIOS CANNOT SEE the drive... so I can normally see and format and install windows 10 on this disk, but after PC reboots bios search for disk to start. see nothing as always and does not start booting cause BIOS cannot find if there is a disk to boot from... 

Share this post


Link to post
Share on other sites
On 1/25/2017 at 7:54 PM, kogoro said:

I finally dowloaded the prema biosmod and the modded bios was inside , i also give a little money to prema to thanks him.

After some hour of search because of some  "resume from hibernation"  problem which didn't allow me to enter the bios non modded  ( problem solved only type  shutdown /s /f /t 0  on the command window and you will have a full shutdown )  i finally found the version of my bios : 1.03.01  , i also found on an other website a newer bios for the computer   (http://forum.notebookreview.com/threads/clevo-bios-older-models-released-in-after-2014.790474/ )  1.05.01 "support for win 10"  , i am already in win 10 ^^ , my question: should i install the premamod bios now or should i update the EC and bios before ????

and second question does the premamod bios change something about pciessd compatibility ? (nvme   3.0  etc. )????

THANKS for reading !

 

did you found any solution about NVME disks support? Thanks in advance

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Similar Content

    • By Axel de S
      Hello guys,
      I have a GT72VR 6RE with G-sync MSI Laptop. Sadly the GPU is partially dead (artefacts all over the screen, crashes, windows detecting a damaged hardware etc...).

      So I bought an other GTX1070 MXM on ebay, which was used in a Vortex G65 6RE before.
      Sadly, when I plug the new GPU in the laptop, the laptop screen stays completly off, but i can use the HDMI port. So i though that I would just have to flash the vbios to the one I was using on the GPU that died, but I couldn't because of a mismatch betwen the PCI Device ID.
      The new GPU ID is : 10DE 1BA1 - 1462 11AF and the previous GPU ID was :10DE 1BE1 - 1462 11AF
      Pretty close right? but the A1 and E1 variation are fcking everything up. I've read that 1BA1 is for non G-sync and 1BE1 is for G-sync. I've also read that the G-sync variation is not part of the card but is an external part no on the GPU board.

      So now I'm wondering what can I do : is there a way to force the vbios flash or to change the PCI ID ? I really need some help here. I'm no expert and I've try as much as I could. Maybe I need to do some vbios editing but I don't really know how to do it and what to do exactly to make this work.

      Thank you very much for your help guys
    • By learnfromit
      alienware 15 r2 970m with i7-6700hq vbios request so i can overclock and mess with voltage.

      BIOS version backup made with techpowerup GPU-z.

      GM204.rom
       
      or can someone re direct me to one already made that will work? all links i find are dead, thanks.

    • By Diky
      help me to unlock amd-v acer aspire one 725
      it's my vars file
      please..
      vars.rar
    • By Awesome14
      I found this: https://photonicsguy.ca/projects/t530
       
      It's a nice how to on altering the whitelist on the W530/T530 laptop.
    • By 9vul14
      Hey allI, I need help  with modding my BIOS. I was wondering if anyone could help me mod my BIOS to unlock the 'Advanced' tab which I don't have on my InsydeH20 F.52 Rev 5.0 Bios? Thanks so much and I look forward to your response! Laptop: HP Pavilion x360  ba109tx
       
      Specs: 
      i7-8550U
      Nvidia Geforce 940MX
      Intel(R) UHD Graphics 620
      12GB DDR4-2400 SODIMM RAM
      128GB SSD, 1TB HDD
       
      Laptop Product Page: https://support.hp.com/gb-en/document/c05650773
      Vanilla BIOS: https://support.hp.com/sg-en/drivers/selfservice/hp-pavilion-14-ba100-x360-convertible-pc/16851098/model/18161600
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.