I am trying my Sager NP 9377 to get to work but to no avail. NO POST, NO DISPLAY.
in short>> powering on laptop causes fans to run at full speed after 10(cpu only) + 10 (now both cpu+gpu) with Caps Lock + Num Lock + Scroll Lock LEDs blinking, continuous 1 second beep, repeats for one minute with 1 second in between, then laptop shuts down.
System Specs are i7 4810mq 8gb gtx 880m SLI variant (though my laptop has other GPU Slot empty so only singular 880m running) 120 Hz display.
> if i take out the battery and plug in AC only, the power light comes on ORANGE
if both battery is connected, then i have both power and battery light ORANGE
and if only battery is connected then of course laptop is waiting for me to press the power button
but in all 3 cases the following happens
> Pressing the power button brings laptop to some signs of life, power LED turns green, both the CPU and GPU fans have a very quick jerk but does not spin., keyboard lights up with Blue Backlight (dont know if this is relevant or not), HDD activity light starts to blink showing HDD access maybe (even when hdd is removed)
> Display remains blank (i dont even sense the display backlight being on)
> HDD activity light sometimes goes off after only 1-2 seconds, sometimes shows rapid blinking/activity for 4-5 seconds
> both fans remain off (i removed back cover to check this)
> after about 10 seconds or so, the CPU fan spins up (speed is normal, just like when using the laptop in IDLE)
> after 10 more seconds have passed, the CPU fan seems to be turning off for a split second then both the CPU and GPU fan turn on full speed with a lot of noise.
> Caps Lock, Num Lock and Scroll Lock LEDs all blink together with single beep for about 1 second, repeats beep with 1 second in between.
> goes on for about 1 minute then laptop shuts down.
> forcing the fans to spin down using FN+1 key makes them spin back up to full speed after a split second (dont even know why i tried this one -_-)
What I Have Tried So Far
> EC and Bios Reset (take out battery, disconnect AC Adapter, disconnect CMOS Battery, Press Power Button for upto 30 seconds)
> Change Ram and check all available slots
> Repaste CPU/GPU and clean out fans
> Checked GPU...... Flashed the 880m in this Sager with MSI vBios and tested it in a MSI Gt70 2PC i have, gpu ran fine, tested with FurMark, AC Odessey, Ghost Recon Wildlands for over an hour (unfortunately the cooling in my MSI is not good enough it already runs hot, and this 880m causes thermal throttling as well as power limit throttling sometimes). Reflash 880m with original Clevo vBios and put back into the Sager, still no boot, same results as before.
> Checked the CPU..........checked the 4810mq in the MSI GT 70 which worked fine, as well as tried the 4810mq from the MSI in the Sager, still no boot.
> Suspected bad GPU fan connection......therefore forced both fans to full speed as soon as i press power button (using FN+1 Keys) and both fans turn on full speed, same results.
> tried charging the battery to the max before turning on on battery only, same results.
>>------- The laptop has had some random shutdowns in the past too during gaming but would turn back on fine after waiting for 10 mins or so, then i sold it to some guy who brought it back to me the next day saying that it just turned off during gaming and wont turn back on, i returned his money, did all the troubleshooting above to no avail. then i finally put it aside to wait until i get some other system in which i can test the CPU and GPU.
Then one day i turned it on (after leaving it untouched for a couple months), same results as above, i decided to try once without battery and it Freakin Turned ON!!!, used it for a couple days without battery, played a few games (thermal throttling was observed here and there), but then this happened again and this time it seems permanent . And now i have not only repeated all the steps above but this time also checked the CPU and GPU in the MSI GT70 too. ------------<<
> touching the CPU heat pipes feels warm, but the GPU heat pipes are colder (GPU never even booted?). dont know if this is normal or not.
> i replaced one of the capacitors near the CPU once, but i did use the laptop for quite a while after that without any issues.
> my Idle temps were always below 40c for both CPU and GPU, so an overheat warning as soon as laptop is powered on seems unlikely (false overheat warning?, but GPU does not even seem to be detected/ booted as heat pipes remain cold to touch), also i repasted the CPU and GPU multiple times.
> The guy who sold me the laptop told me that the power adapter was originally a Dell, and it was modified to use with this Sager by replacing the cable with a 4-Pin one from a Toshiba (same pinout as the Sager), but then again i have used this laptop for quite a while on the same adapter.
> From day 1 of having this laptop, some keys on the keyboard (w, s, t, c and numpad 4) did not work 99% of the time. pressing really hard on any one of them sometimes made ALL of them work for a while. any thoughts on this issue?? (even if its unrelated).
So what seems to be the issue here?
GPU not detected ?, False temperature alert?, Bad fan?.
Any help towards resolving this will be greatly appreciated.
Thanks in advance .
I recently purchased a replacement 980M (Clevo model) for my P770DM-G after the original died, however, after installing the card the laptop doesn't boot. I only get a black screen, and after a couple minutes the fans spin to max before shutting down, which is the same thing that happens when I try to boot it without any gpu at all. I've tried the reset procedure, unplugging, removing battery, and removing CMOS, to no avail. It does beep before shutting down (I counted 22 times exactly). Anyone have any insight as to what the problem is?
By Axel de S
I have a GT72VR 6RE with G-sync MSI Laptop. Sadly the GPU is partially dead (artefacts all over the screen, crashes, windows detecting a damaged hardware etc...).
So I bought an other GTX1070 MXM on ebay, which was used in a Vortex G65 6RE before.
Sadly, when I plug the new GPU in the laptop, the laptop screen stays completly off, but i can use the HDMI port. So i though that I would just have to flash the vbios to the one I was using on the GPU that died, but I couldn't because of a mismatch betwen the PCI Device ID.
The new GPU ID is : 10DE 1BA1 - 1462 11AF and the previous GPU ID was :10DE 1BE1 - 1462 11AF
Pretty close right? but the A1 and E1 variation are fcking everything up. I've read that 1BA1 is for non G-sync and 1BE1 is for G-sync. I've also read that the G-sync variation is not part of the card but is an external part no on the GPU board.
So now I'm wondering what can I do : is there a way to force the vbios flash or to change the PCI ID ? I really need some help here. I'm no expert and I've try as much as I could. Maybe I need to do some vbios editing but I don't really know how to do it and what to do exactly to make this work.
Thank you very much for your help guys
alienware 15 r2 970m with i7-6700hq vbios request so i can overclock and mess with voltage.
BIOS version backup made with techpowerup GPU-z.
or can someone re direct me to one already made that will work? all links i find are dead, thanks.