Jump to content
EwinRacing Flash Series Gaming Chairs
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By mtvgt
      Hi guys,
      i have m18x R1 model with A05 unlocked bios and i try to connect ati mobility 4870 card/s.
      I read ton of posts but people that seem to have similar problem with different card didn't post any solution. Case is when i connect 4870 i get black screen and 8 beeps.
      When i use only integrated graphics (no cards installed) laptop is starting normally.
      When i use integrated graphics (nvidia card installed as master) laptop is starting normally.
      When i use nvidia card installed as master laptop is starting normally.
      When i use nvidia card installed as master and ati 4870 installed as slave laptop is starting normally but in devices manager i see there is error 10 with ati card.
      When i use ati 4870 card installed as master i get 8 beeps and black screen.
      I tried to google for answers but unfortunatelly didn't find any. Do you know if that old card can work in m18x ? Maybe it's not supported at all? Do you have any ideas what else can i try?
    • By GrisGris
      For when that rubber coating on your laptop phase shifts to fly paper...
       
      Here is what I did,
       
      Disassemble M18x:
      Well documented by debaucher:
      The palm rest section was the biggest offender for me;

      >I used a plastic spoon and nail polish remover to remove the rubber coating:
      >Obviously remove as many of the various utility boards as possible.
      >I left the touch pad in place because this model used thermally fused plastic rivet like pieces to hold the light pipes in place and I found it easier to mask it off.
      >"FrogTape Delicate Surface" worked very well for masking off various surfaces

      >I used Krylon Plastic Paint as a base coat and 'Jet Black metal flake Automotive Paint;

      >With the paint still setting up I dusted various glow powders over the substrate and dusted some additional black paint to achieve some depth to the effect .
      >I after the automotive paint set up I use mate clear coat the overcoat the entire surface. I personally believe glossy clear coat would not look as good. 
      >Adjust as needed and re-assemble.

      >I Used a USB LED clamp light available ebay/amazon $10 to illuminate
       
      Hope you enjoyed the first post...
      .
    • By p1npo1nt
      I'm going to be upgrading my Alienware M18x R1 with a GTX770m I purchased from ebay; 770m has a Dell P/N: HW6C9 for reference. I have a couple questions about performing this upgrade:

      -Is the /unlocked/ version A05 bios necessary? I am receiving 8 beeps on startup with the dell factory A05 bios installed w/ the 770m
      -Is a vBIOS flash required for basic functionality and driver installs? 
      -If so, is there a link to a compatible vBIOS for this card, finally, a guide for installing the new vbios?

      Any help is vastly appreciated, I've done some homework but I am new to upgrading MXM modules on laptops. 
    • By Henrik9979
      First I want to thank the community, who have inspired me to do this project.
      I will give you guys the chance to follow me on this journey.
       
      I hope you will all help me come up with ideas, techniques and parts that could become handy.
       
      This modding may be possible to convert to allot of laptops.
       
      Let's begin!
      Here is the measurement of the went hole.
      77mm X 16mm

       
      I have 2 ideas for what can be done.
       
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.