Jump to content
DgknGkdn

LenovoLenovo Y510P Video Card Update issue [Windows 10]

Recommended Posts

The computer I used was '' Lenovo Y510P ''. There is a '' Nvidia GT755M [SLI] '' as a display card. I have tried both ways of downloading the video card driver from both GeForce Experience and Nvidia driver site. Both kinds of graphics cards are starting to update. Later, the 'graphic driver is installed' part of the screen goes and never comes again. I can not enter Windows when I turn off the computer. I have to take format from scratch.

After formatting, Windows automatically loads a graphics card driver in 2017, trying to update the driver again, it stays black on the screen again. I have to format again.

With DDU (Display Driver Uninstaller) program, I deleted the old video card driver and updated it again. But I met the same problem.

I communicated with Nvidia and stated that I had such a problem. They asked me not to install the 388.13 video card driver. That graphics card driver has been loaded without any problems. But I have the same problem with all the video card drivers out there.
 

NOTE: This problem only happens on Windows 10. I can update the display board without any problems in operating systems like Windows 8,8.1.
 

NOTE: I have been having this problem for about 2 months, before I could update my display card in Windows 10 without a problem.


The driver I am currently using is: 388.13

Share this post


Link to post
Share on other sites

I had the exact same problem. I removed the video card from the expansion port. Then I installed the driver, rebooted. The I shut the system down and replaced the card and restarted. SLI is fully functional. 

Share this post


Link to post
Share on other sites
4 hours ago, adam.jakey said:

I had the exact same problem. I removed the video card from the expansion port. Then I installed the driver, rebooted. The I shut the system down and replaced the card and restarted. SLI is fully functional. 

So, do you have any problems when you open it? When I turn it on, the computer gets stuck, and it turns out when I open it. Then again the same problem continues.

Share this post


Link to post
Share on other sites

No, the problem since has gone away. Maybe your expansion video card is bad. How does it run with it removed?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By ounces
      After spending significant time and effort to obtain "DC" screen for 8770w (which is essentially a regular IPS panel with fancy board that converts 8bpc LVDS to 10bpc DP), I have finally got and installed one. All works great, except of the one problem...

      It has pretty bad banding / posterization in lower shadows. I have tried profiling it in different modes (full range, sRGB, rec709) - issue persists, and it indeed shows only in the lowest part of the characteristic curve. Mids and highlights are represented fine and show low deviation from reference values.

      GPU is HP K4000M, Nvidia drivers installed "as it is", video-card is identified without a hitch.
      Banding was not present with the original TN panel using the same GPU.
       
      While checking a software side, I have noticed that Win10 has bit depth set to 8-bit...
       

       
      My initial reaction was, - "Easy, let's change it in `nvidia-settings` and we're all set":

      ...but that would be too easy, right? After selecting 10bpc and clicking "Apply" screen went off and back on, only to show that depth stayed at 8bpc. Repeating the above few times yielded exactly the same result and I'm not in a hurry to meet a cliched (and laymen) definition of insanity.
       
      Let's check GPU-Z. So far so good, nothing unusual. Notice the highlighted BIOS version and subvendor string:
       
      Time to delve into other tabs. We are running WDDDM v2.4 which supports GPU dithering, but hey... BIOS version has changed!
       
      Briefly back to `nvidia-settings` to check what is reported by vendor's own utility:

       
      So far, we have two strings for BIOS version:
      80.04.5A.00.02 (let's call it an "A") 80.4.33.0.37 (let's call it a "B")  
      Notice how 2nd one seems to not follow hexademical notation. Lastly, "NVIDIA BIOS" drop-down, reports "A" version:
       
      ...and monitor section which confirms that rig is indeed capable of 10bpc, but currently running at mere 8bpc:

       
      Windows "Adapter settings", reports version "B". It's 2019, diversity is a must.

       
      "NVidia inspector" is of the same opinion:

       
      Now, let's use some seriously legit tools and check-in exported BIOS file in `nvflash`:

       
      Here we have two three interesting findings:
      Reported vendor is Dell, not an HP. See this link for details. BIOS version is back to "A". Have I already mentioned diversity? MXM module uses MX25L2005 flash storage in WSON-8 packaging. If things go real nasty, we should be able to rescue a patient via Pomona clip and external programmer.  
      Loading the same file in "Kepler BIOS tweaker" confirms the facts:

       
      EDID settings, courtesy of NVidia Control Panel. Hex dump can be found at the bottom of this post.
      ...Shall I be worried about "60.02Hz" refresh rate?
       
      To summarize:
      Why two different BIOS versions are reported? Anything to do with UEFI (e.g. HP is sideloading its own during boot)?.. Why two different vendors reported? As far as I remember, this is branded HP GPU. Where to get "clean" BIOS of K4000M for future experiments? Ideally from 8770w equipped with "DreamColor" panel from a factory.  
      Link to the dumps, BIOS ROM and monitor EDID: https://mega.nz/#F!zGgRmQIL!9q2QFZtHuK2RQ-WHXMA4Mg (also attached to this post)
      K4000M.zip
    • By Blocker35
      Hi guys, bit of a rookie to the whole EGPU scene. Currently I have:
       
      - MacBook Pro 2015 13inch (3.1GHz Core i7 16GB RAM)
      - Razer X Core 
      - Apple TB3 to TB2 Adapter
      -  TB2 Cable (Cable Matters)
      - 23inch AOC External Monitor
       
      I am wonder about what graphics card to get to run X-Plane11 with high graphic settings?
      I have purgewrangler set up and ready to use with an AMD graphics card, but am also open to the idea of an Nvidia graphics card.
      Any advice appreciated. I did not buy a Windows PC as I need a Mac for various other things and wanted an all-in-one laptop.
    • By can rx
      Hello to all dear visitors, 
       
      I have been using Lenovo y510p notebook for two years but in games I think my graphic card is inadequate. After that I've bought Mini PCI-e EXP GDC and attached it to where the wireless card socket is.  However because it has x1 speed its performance is too low. Even though on tests rx460's ranks is low than rx480, it has more performance.
       
      In x1 PCI-e port, the performance is too low and inefficient. On GPUz programme, use of memory controller is 20% but use of GPU is 100%. I mean, I've been hooked to the x1 speed.
       
      Components : EXP GDC version 8.0 +450w PSU + rx480
       
      I've read all pages about ultrabay, I want to buy and to share in forum.
       
      If anyone has ultrabay to PCI-e port, I want to buy. Please help.
       
      Thanks for everything.
    • By PrecastFlame
      Hi, I'm having problems trying to connect a GTX 750 Ti to my Lenovo T420 using the dock EXP GDC Beast (express card version).
      My laptop: Lenovo T420
      RAM: 8GB DDR3
      CPU: Intel Core i5 2520M
      GPU: Intel HD Graphics 3000
       
      My problem is: if I plug the express card and I turn on the laptop it doesn't boot up and the screen becomes horrible, with coloured pixels and a sound like "bip-bip".
      If I try plugging the express card when the laptop is already turned on it sees the gpu, but if try installing the drivers I have to apply the modifies restarting the computer.
      I hope you understood my problem (I don't speak English very well).
      Please help me, It's making me crazy!
       
      EDIT: I didn't say that if I plug the express card when the pc is already turned on, in the device menager there is "Error 12" on the gtx 750 ti
    • By Kel
      I got the exp gdc beast 8.5 got all the connections right... laptop boots up... fans turn on the gpu.... device manager detects gtx 1060 with a “ ! “ in a yellow triangle. Now what to do.... i tried to do the bios mod.... but realised that i have 3.07 version. 
      Questions-
      1 is there any way to get this done without the mod?? 
      2 if mod is the only way... kindly help me with step by step instruction in laymans terms... i m not a techy... so i might not understand technical terms.... altho i am interested... but learning yet. Please help. 
×

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.