Jump to content
EwinRacing Flash Series Gaming Chairs
Sign in to follow this  
Officer Winters

Thermal Pads Not Properly Installed?

Recommended Posts

Hey guy I recently bought a Lenovo Y510P and I am NOW quite aware of its issues but a cool machine non the less. As I was taking it apart to replace the thermal compound I was also replacing the thermal pads with thicker ones (all that I had) now my temps haven't changed not sure maybe its due to the thinker pads but as I was removing the old ones. I saw that 2 or 3 still had the sticker on the side facing the heat sink. Normally I remove both adhesive sides of the thermal pads where as these still had one side with the plastic on it. What do you guy make if this? Thanks. 

Share this post


Link to post
Share on other sites

The thermal pads I have two sides of plastic, so all you need to do is remove it. It's just there to help keep it clean and fresh for application.

 

As for temps they probably will only change 1-2c but that depends on how cheap and dried out the OEM's were.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Content

    • By IronPancakes
      Hey guys, first post, but I thought I’d discuss my heatsink fan retrofit in my old M14x r1. 
       
      Old fan was loud and not very efficient: the air transfer rate was around 2 cfm (I’m assuming cubic feet per minute). Finally had enough and decided to swap out the crappy r1 fan/coughing pinwheel for a r2 fan (rated at 10.4cfm). 
       
      I found an old r2 heat sink on eBay (beware though that the heat sink for the r2 will NOT fit the gpu/cpu configuration for the r1. HOWEVER, the fan of the r2 heat sink it is attached to is a carbon copy fit into the r1 MoBo. A few philips head screws and a seal of good electric tape and BAM, you’ve got a significantly cooler and MUCH quieter intake fan in your old R1. 
       
      My CPU temps from before were around 87-88 max load in FSX, 65 for the GPU; bear in mind this is after a repaste. Now with the new fan, I’m not going over 77 degrees on the CPU, and the gpu stays around 58, all while being MUCH quiter. I’ll post pics of the walkthrough if anyone is interested.
       
       Just thought I’d share with all you fellow loonies trying to squeeze every last frame and degree out of our “portable toaster ovens with a screen and keyboard”. 
       
       
    • By zaxx7
      This is my first post and I'd appreciate any help you guys can offer. 
       
      I've been using my AW M18x r1 since I bought it new. 
       
      Basics:
      I7 2760qm sandybridge
      Bios A5
      16 gb ram
      Radeon 6990m 2gb 
       
      I used to run 2 6990m's, but the primary died 3 yrs ago and I replaced it with the secondary card. Been working great until this week. 
       
      I'm using hwinfo64 for fan monitoring. 
       
      I started having lock-ups to black screen, grey screen or black with white vertical lines. I noticed my shader temp on my GPU was running out of control whenever I start  game or even run a video. The other temps seem to be in the normal range. The shader will jump from 39 C to 70 C almost immediately and then upwards from there. Over 100 C when I 1st caught it. I assume it's thermal shutdown. 
       
      I'm using the legacy driver for my card 15.7.1. 
       
      I'm willing to buy a new card, I'm looking at a 780m, but I want to figure out if it's just an issue with the card. 
       
      Any suggestions on testing for other issues? Why would it be the shader only, or is that just an issue with Hwinfo64? 
       
      Thanks in advance. 
       
       
    • By Irons324
      Hey everyone. 
       
      Inspired by P-Mac's eGPU build, I decided to finally go ahead and build one. It was a toss up between building a Hackintosh beast or eGPU for my MBP, and I decided the eGPU for cost. I'm avidly against Windows as an OS so I'm using Sierra.  Long story short, I knocked it all together in about an hour and a half, ran the scripts and fired it up. No issues recognising the eGPU is there, it's running my 32" 720p TV I've been using for a monitor no problems. I essentially wanted some more oomph out of my gaming experience (I'm a relatively dedicated WoW player) so I was very excited to fire up the game and max out some settings.
       
      However, booting into the game I was getting less FPS than what I was getting on the GT 750m. I had the settings tweaked to allow 60fps in low load situations. Using the eGPU I was getting around 40, and my recommended settings went from 4 to 1. The GPU also got hot FAST and the fans spooled up, which I read is uncommon. The MBP also starts ventilating quickly. I've used Cinebench to benchmark the setup and got 77fps within OSX. To me this seems like I should be able to run WoW at high settings on 720p... 
       
      Tips for what I've done wrong in the setup, or what I can change or implement? Do I need to use Optimus? 
       
      EDIT: I just ran the CPU benchmark as well and got what seems like a low(?) score, could this be affecting my setup?
       
      Thanks all. 


    • By Dr. AMK
      Do I need to change the thermal pads for GTX 780m every time I want to repast? if so, what is the rghit thikniss for it? and where can I but it?
      Clevo P570wm - GTX 780m SLI
       
      Best Regards,

    • By Sourumizoki
      Hi guys!
      I have a lenovo notebook y510p, I have obtained a ErgoStand II coolerpad to reduce even slightly its temperature, but I have not noticed significant difference, I have seen on many forums that recommend NotePal X3 for play equipment, need to know if anyone has had the oprtunidad to test both cooler and give me advice, greetings, sorry for the bad English.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.